JOURNAL BROWSE
Search
Advanced SearchSearch Tips
A Preliminary Study on Fatigue Strength of High Toughness Thermoplastic Composite Material AS4/PEEK
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
A Preliminary Study on Fatigue Strength of High Toughness Thermoplastic Composite Material AS4/PEEK
Song, Ji-Ho; Gang, Jae-Yun;
  PDF(new window)
 Abstract
First, various specimen geometries, namely, coupon type, waisted type and dog-bone type, were examined to determine appropriate fatigue specimen of thermoplastic composite material AS4/PEEK and the n, fatigue strength of smooth and notched specimens of AS4/PEEK [-45/0/+45/90]2s was investigated. Fatigue tests were performed under load controlled condition at a stress ratio of 0. 1 at a frequency of 5Hz. Stiffness degradation of specimens with fatigue cycling was monitored using an automated unloading compliance technique. The waisted type specimen is found appropriate for smooth fatigue specimen geometry of AS4/PEEK. As for the effect of stress concentration, it is found that fatigue strength is higher for a 2mm-diameter hole notched specimen than a 5mm-diameter one. Fatigue notch factor decreases with the increase of fatigue life. These results are far different from the trend of fatigue strength of metallic materials. The stiffness variation of smooth specimen was only 4% at maximum until final fracture. On the other hand, the stiffness of hole notched specimen was reduced by 45% at maximum. Notched fatigue strength was compared between thermoplastic composite AS4/PEEK and thermosetting composite Graphite/Epoxy. In long-life fatigue (>104), the AS4/PEEK composite shows superior fatigue strength, but in short-life fatigue, the fatigue strength of the Graphite/Epoxy composite is nearly equal or somewhat higher than that of the AS4/PEEK composite,
 Keywords
Fatigue Strength;Thermoplastic Composite;Fatigue North Factor;Thermosetting Composite;Stiffness Degradation;Stress Redistribution;
 Language
Korean
 Cited by
 References
1.
Nisitani, H., Noguchi, H., Yamaguchi, T. and Kim, Y.H., 1991, 'Fatigue Strength of Plain and Notched Specimens of Thermoplastics (In the Case of Polyethe retherketone),' Trans. Jpn. Soc. Mech. Engrs A, Vol. 57, No. 540, pp.1659-1699

2.
Nisitani, H., Noguchi, H. and Kim, Y.H., 1992, 'Evaluation of Fatigue Strength of Plain and Notched Specimens of Short Carbon-Fiber Reinforced Polyetheretherketone in Comparison with Polyether etherketone,' Engng Fract. Mech., Vol. 43, No. 5, pp. 685-705 crossref(new window)

3.
Nisitani, H., Noguchi, H. Kim, Y.H. and Yamaguchi, T., 1992, 'Fatigue Strength of Plain and Notched Specimens of Short Carbon- Carbon Fiber Reinforced Poly-Ether-Ether-Ketone (In Comparison with Poly-Ether-Ether-Ketone),' J. Soc. Mat., Japan, Vol. 41, No. 464, pp. 740-745

4.
Noguchi, H., Nisitani, H., Kim, Y.H. and Yamaguchi, T., 1992, 'Torsional Fatigue Process in Short Carbon-Fiber Reinforced Polyamid 6.6 (Comparison with Fatigue of Rotating Bending),' Trans. Jpn. Soc. Mech. Engrs A, Vol. 58, No. 553, pp. 1555-1560

5.
Nisitani, H., Noguchi, H. and Kim, Y.H., 1993, 'Fatigue process in Short Carbon-Fiber Reinforced Polyamide 6.6 under Rotating-Bending and Torsional Fatigue,' Engng Frac. Mech., Vol. 45, No. 4, pp. 497-512 crossref(new window)

6.
Noguchi, H., Nishizawa, A., Nisitani, H. and Kim, Y.H., 1994, 'Miner's Rule for Fatigue Life of Short Carbon Fiber Reinforced Poly-Ether-Ether-Ketone,' J. Soc. Mat., Japan, Vol. 43, No. 489, pp. 672-678

7.
Noguchi, H., Kim, Y.H. and Nisitani, H., 1995, 'On the Cumulative Fatigue Damage in Short Carbon Fiber Reinforced Poly-Ether-Ether-Ketone,' Engng Frac. Mech., Vol. 51, No. 3, pp. 457-468 crossref(new window)

8.
Tai, N.H., Ma, C.C.M. and Wu, S.H., 1995, 'Fatigue Behavior of Carbon Fiber/PEEK Laminate Composites,' Composites, Vol. 26, No. 8, pp. 551-559 crossref(new window)

9.
Im, K.H., Kim, J.H. and Yang, I.Y., 1998, 'A Study on Residual fatigue Bending Strength and Damage Behavior of CFRP Composites Subjected to Impact Loadings,' KSME Int. J., Vol. 12, No. 1, pp. 50-57

10.
Song, D.Y. and Otani N., 1998, 'Approximate Estimation of Fatigue Strength of Polymer matrix Composites by Material Properties,' Material Science and Engineering A, Vol. 254, pp.200-206 crossref(new window)

11.
Curtise, D.C., Moor, D.R. and Zahlan, N., 1988, 'Fatigue Testing of Multi-Angle Laminates of CF/PEEK,' Composites, Vol. 5, No. 6, pp. 446-452 crossref(new window)

12.
Henaff-Gardin, C and Lafie-Frento, M.C., 1992, 'Fatigue Behavior of Thermoset and Thermoplastic Cross-Ply Laminates,' Composites, Vol. 23, No. 2, pp. 109-116 crossref(new window)

13.
Simonds, R.A. and Bakis, C.E. and Stinchomb, W.W, 1989, 'Effects of Matrix Toughness on Fatigue Response of Graphite Fiber Composite Laminates,' ASTM STP 1012, pp. 5-8

14.
Bakis, C.E., Simonds, L.W. and Stinchomb, W.W., 1990, 'Matrix Toughness, Long-Term Behavior and Damage Tolerance of Notched Graphite Fiber-Reinforced Composite Materials,' ASTM STP 1059, pp. 349-370

15.
Simonds, R.A. and Stinchomb, W.W., 1989, 'Response of Notched AS4/PEEK Laminates to Tension/Compression Loading,' ASTM STP 1044, pp. 133-145

16.
Oh, C.H., Earmme, Y.Y. and Song, J.H., 1997, 'Automated Real-Time Measurements of Fatigue Crack Length and Crack Opening Load Using Unloading Elastic Compliance Method,' Int. J. of Fatigue, Vol. 19, No. 2, pp. 169-176 crossref(new window)

17.
Peterson R.E., 1974, Stress Concentration Factors, John Wiley & Sons Inc., New York, pp. 37

18.
Tan, S.C., 1988, 'Finite-Width Correction Factors for Anisotropic Plate Containing a Central Opening,' J. of Composite Materials, Vol. 22, pp. 1080-1097 crossref(new window)

19.
Dowling, N.E., 1993, Mechanical Behavior of Materials, Prentice-Hall, New Jersey, pp. 408-411

20.
김정규, 김도식, 1993, 'Glass/Epoxy 복합재료의 피로강도평가 및 피로수명예측,' 대한기계학회 논문집, 제7권, 제10호, pp. 2475-2482

21.
Tan, S.C., 1989, 'Mixed-Mode Fracture of Notched Unidirectional and Off-Axis Laminates under Tensile Loading,' J. of Composite Materials, Vol. 23, pp. 1083-1105 crossref(new window)

22.
김정규, 김도식, 1992, '원공을 가진 Glass/Epoxy 복합재료의 노치강도 및 파손조건,' 대한기계학회 논문집, 제16권, 제7호, pp. 1285-1293

23.
김형근, 황운봉, 한경섭, 1991, '적층판 복합재료의 원형노치에 의한 노치강도,' 한국항공우주학회지, 제19권, 제3호, pp. 41-51

24.
Kellas, S., Morton, J. and Curtis, P.T., 1991, 'A Characteristic Fatigue Parameter for Notched Composites,' Int. J. of Fatigue, Vol. 13, No. 1, pp. 35-43 crossref(new window)

25.
Hwang, W. and Han. K.S., 1986, 'Fatigue of Composites-Fatigue Modulus Concept and Life Prediction,' J. of Composite Materials, Vol. 20, pp. 154-165 crossref(new window)

26.
Daken, H.H and Mar, J.W., 1985, 'Splitting Initiation and Propagation in Notched Unidirectional Graphite/Epoxy Composites Under Tension-Tension Cyclic Loading,' Composite Structures, Vol.4, pp. 111-133 crossref(new window)

27.
日本複合材科學會, 1989, 複合材科ハソト ブック, 日刊工業新刊社, 東京, pp. 243

28.
成澤郁夫, 1986, ブ?スシクの强度設計と選び方, 工業調査會, 東京, pp. 15