Numerical Simulation of Flow and Heat Transfer Characteristics of Impinging Jet Using $\small{k-{\varepsilon}-{\overline{v^{$ Model

Title & Authors
Numerical Simulation of Flow and Heat Transfer Characteristics of Impinging Jet Using $\small{k-{\varepsilon}-{\overline{v^{$ Model
Choi, Bum-Ho; Lee, Jung-Hee; Choi, Young-Ki;

Abstract
This study deals with jet impingement, which is extensively used in the process industries to achieve intense heating, cooling or drying rates and also widely employed as a test flow for turbulent models due to its complex flow configuration, on a flat plate by numerical methods. In this calculation, the finite volume method was employed to solve the Navier-stokes equation based on the non-orthogonal coordinate with non-staggered variable arrangement. To get a better understanding for the fluid flow and heat transfer characteristics of the turbulent jet impingements, $\small{k-{\varepsilon}-{\overline{v^{$ turbulent model was adapted and compared with the experimental data and the result of standard $\small{k-{\varepsilon}}$ turbulent model. Numerical calculations were carried out with various flow rates, nozzle to plate distances. In the case of the axisymmetric jet impingement on a flat plate, $\small{k-{\varepsilon}-{\overline{v^{$ turbulent model showed better agreement with the experimental data than the standard $\small{k-{\varepsilon}}$ turbulent model in the prediction of the mean velocity profiles, the turbulent velocity profiles. the turbulent shear stress and the heat transfer rate. The highest heat transfer rate can be obtained when the impingement occurs within the potential core..
Keywords
Jet Impingement Cooling;Non-orthogonal Coordinate;Elliptic Relaxation;Non-staggered Arrangement;
Language
Korean
Cited by
References
1.
Gardon, R. and Akfirat, J. C., 1966, 'Heat Transfer Characteristics of Impinging Two-Dimension Air Jets,' ASME J. of Heat Transfer, pp. 101-108

2.
Giralt, F. and Chia, C. J., 1977, 'Characterization of the Impingement Region in an Axisymmetry Turbulent Jet,' Ind. Eng. Chem. Fundam., Vol. 16, pp. 21-28

3.
Craft, T. J., Graham, L. J. W. and Launder, B. E., 1993, 'Impinging Jet Studies for Turbulence Model Assessment - II. An Examination of the Performance of Four Turbulence Models,' Int. J. Heat Mass Transfer, Vol. 36, No. 10, pp. 2685-2697

4.
Cooper, D., Jackson, D. C., Launder, B. E. and Liao, G. X., 1993, 'Impinging Jet Studies for Turbulence Model Assessment - I. Flow-Field Experiments,' Int. J. Heat Mass Transfer, Vol. 36, No. 10, pp. 2675-2684

5.
Jambunathan, K., Lai, E. Moss, M. A. and Button, B. L., 1992, 'A Review of Heat Transfer Data for Single Circular Jet Impingement,' Int. J. Heat and Fluid Flow, Vol. 13, No.2, pp. 106-115

6.
Huang, L., EI-Genk, M. S., 1994, 'Heat Transfer of An Impinging Jet on A Flat Surface,' Int. J. of Heat Mass Transfer, Vol. 37, No. 13, pp. 1915-1923

7.
Lee, S. J., Lee, J. H., and Lee, D. H., 1994, 'Local Heat Transfer Measurements From an Elliptic Jet Impinging on a Flat Plate Using Liquid Crystal,' Int. J. of Heat Mass Transfer, Vol. 37, No.6, pp. 967-976

8.
Durbin, P. A., 1991, 'Near-wall Turbulence Closure Modeling Without 'Damping Functions,' Theoretical and Computational Fluid Dynamics, Vol. 3, No. 1, pp. 1-13

9.
Rhie, C. M., 1981, 'A Numerical Study of The Flow past an Isolated Airfoil with Separation,' Ph. D. Thesis, Dept. of Mech., Univ. of Illinois at Urbana-Champagn

10.
Kim, J., and Moin, P, and Moser, R., 1987, 'Turbulent Statistics in Fully Developed Channel Flow at Low Reynolds Number,' J. Fluid Mech., Vol. 177, pp. 133-166