JOURNAL BROWSE
Search
Advanced SearchSearch Tips
Evaporation Heat Transfer and Pressure Drop Characteristics of Refrigerant R-22 in a P1ate and Shell Heat Exchanger
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Evaporation Heat Transfer and Pressure Drop Characteristics of Refrigerant R-22 in a P1ate and Shell Heat Exchanger
Seo, Mu-Gyo; Park, Jae-Hong; Kim, Yeong-Su;
  PDF(new window)
 Abstract
The evaporation heat transfer coefficient and pressure drop for refrigerant R-22 flowing in the plate and shell heat exchanger were investigated experimentally in this study. Two vertical counterflow channels were farmed in the exchanger by three plates of commercial geometry with a corrugated trapezoid shape of a chevron angel of 45 ° Upflow boiling of refrigerant R-22 in one channel receives heat from the hot downf1ow of water in the other channel. The effects of the mean vapor quality, mass flux, heat flux and pressure of R-22 on the evaporation heat transfer and pressure drop were explored. The quality change of R-22 between the inlet and outlet of the refrigerant channel ranges from 0.03 to 0.05. The present data showed that both the evaporation heat transfer coefficient and pressure drop increase with the vapor quality. At a higher mass flux, the evaporation heat transfer coefficient and pressure drop are higher for the entire range of the vapor quality Raising the imposed wall heat flux was found to slightly improve the heat transfer, while at a higher refrigerant pressure, both the heat transfer and pressure drop are slightly lower.
 Keywords
Plate and Shell Heat Exchanger;Refrigerant;Heat Transfer Coefficient;Vapor Quality;Pre-Heater;
 Language
Korean
 Cited by
1.
Plate and Shell 열교환기내의 R-22 증발열전달 및 압력강하 특성에 관한 실험적 연구,서무교;박재홍;김영수;

대한기계학회논문집B, 2001. vol.25. 10, pp.1318-1326 crossref(new window)
 References
1.
Focke, W. W., Zachariades, J. and Oliver, I., 1985, 'The Effect of the Corrugation' Inclination Angle on the Thermo-hydraulic Performance of Plate Heat Exchangers,' Int. J. Heat Mass Transfer, Vol. 28, No.8, pp. 1469-1479 crossref(new window)

2.
Cooper, A. and Usher, J. D., 1983, Heat Exchanger Design Handbook, Chap. 3.7, Hemisphere Publishing, New York

3.
Bounpane, R. A. and Troupe, R. A., 1985, 'A Study of the Effects of Internal Rib and Channel Geometry III Rectangular Channels,' AIChE Journal, Vol. 15, No, 4, pp. 585-596 crossref(new window)

4.
Bogaert, R. and Boles. A., 1992, 'Global Performance of a Prototype Brazed Plate Heat Exchanger in a Large Reynolds Number Range,' Experimental Heat Transfer, Taylor & Francis, No.8, pp. 293-311

5.
Shah, R. K and Focke, W. W., 1988, 'Plate Heat Exchangers and Their Design Theory,' in Shah, R. K, Subbarao, E. C., Mashelkar, R. A. (Eds.), Heat Transfer Equipment Design, Hemisphere, Washington, DC, pp. 227-254

6.
ASME J. Heat Transfer, 1989. vol.111. pp.300-313

7.
Kandlikar, S. G. and Shah, R. K., 1989, 'Multipass Plate Heat Exchangers Effectiveness -NTU Results and Guidelines for Selecting Pass Arrangements,' ASME J. Heat Transfer, Vol. 111, pp. 300-313

8.
Shah, R. K. and Wanniarachchi, A. S., 1992, 'Plate Heat Exchanger Design Theory,' Industrial Heat Exchangers, J.M. Buchlin, ed., Von Karman Institute for Fluid Dynamics, Belgium

9.
Farrell, P., Wert, K. and Webb, R., 1991, 'Heat Transfer and Friction Characteristics of Turbulent Radiator Tubes,' SAE Technical Paper Series, No. 910197

10.
Collier, J. G., 1981, 'Convective Boiling and Condensation,' 2nd Ed. McGrqwHill, New York, pp. 26-69

11.
Shah, R. K. and Focke, W. W., 1988, 'Plate Heat Exchangers and Their Design Theory,' Heat Transftr Equipment Design, Hemisphere, Washington, DC, pp. 227-254

12.
Kline, S. J. and McClintock, F. A., 1953, 'Describing Uncertainties III Single Sample Experiments,' Mechanical Engineering, Vol. 75, No.1, pp. 3-12

13.
Kattan, N., Thome, J. R. and Favrat, D., 1998, 'Flow Boiling in Horizontal Tubes Part 2-New Heat Transfer Data for Five Refrigerants,' Trans. ASME, Vol. 120, pp. 148-155

14.
Yi-Yie Yan, Tsing-Fa Lin, 1999, 'Evaporat ion Heat Transfer and Pressure Drop of Refrigerant R-134a in a Plate Heat Exchanger,' Int. J. Heat Mass Transfer, Vol. 121, pp. 118-127

15.
Kandlikar, S. G., 1990, 'A General Correlation for Saturated Two-Phase Flow Boiling Horizontal and Vertical Tubes,' Trans. ASME, Vol. 112, pp. 219-228

16.
Shah. M. M., 1982, 'Chart Correlation for Saturated Boiling Heat Transfer Equations and Further Study,' ASHRAE Transactions, Vol.88, pp. 185-196

17.
Akers, W. W., Dean, H. A. and Crosser, O., 1958, 'Condensation Heat Transfer within Horizontal Tubes,' Chem. Eng. Prog. 54,. pp. 89-90

18.
Shah, R. K., .1978, 'Compact Heat Exchanger Selection Methods,' Heat Transfer, Vol. 4, pp. 185-191

19.
Gaiser, G. and Kottke, V., 1989,' 'Flow Phenomena and Local Heat and Mass Transfer in Corrugated Passages,' Chem. Eng. Tech, No. 12, pp. 400-405

20.
Kim, N. H. and Cho, J. P., 1999, 'Experimental Investigation of R-22 Condensa -tion in Tubes with Small Inner Diameter,' Journal of Air-Conditioning and Refrigeration, Volume 7, pp. 45-54

21.
Byun. J. H and Lee. K. J, 2000, 'An Experimental Study of Condensation in Plate Heat Exchangers with R-410A,' Proceedings of the KSME 2000 Spring Annual Meeting B, pp. 304- 310