Advanced SearchSearch Tips
Study on Condensation Heat Transfer and Pressure Drop Characteristics of R-22 in Brazed Plate Heat Exchanger
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Study on Condensation Heat Transfer and Pressure Drop Characteristics of R-22 in Brazed Plate Heat Exchanger
Jeon, Chang-Deok; Gwon, O-Gap; Lee, Jin-Ho;
  PDF(new window)
Experimental study has been carried out on the characteristics of pressure drop and heat transfer of brazed plate heat exchangers using R-22. Data are presented for the following range of variables: the mass flux (40∼90kg/s), chevron angle (, , ) and inlet pressure of the refrigerant (1.4 and 1.6MPa). For both subcooled and two-phase flow, as chevron angle increases, pressure drop and heat transfer coefficient decrease. Condensation heat transfer coefficient and pressure drop were compared with the previously proposed correlations. Among therm, Traviss correlation agreed with experimental results within -40%∼-84% for heat transfer coefficient and -59%∼62% for pressure drop.
R-22;Brazed Plate Heat Exchanger;Condensation Heat Transfer;Pressure Drop;
 Cited by
용접식 판형 열교환기의 성능에 관한 실험적 연구,김종하;권오경;윤재호;이창식;

설비공학논문집, 2002. vol.14. 1, pp.83-90
Buonopane, R. A., Troupe, R. A. and Morgan, J. C., 1963, 'Heat Transfer Design Method for Plate Heat Exchangers,' Chemical Engineering Progress, Vol. 59, No. 7, pp. 57-61

Jackson, B. W., Troupe, R. A., 1966, 'Plate Heat Exchanger Design by ${\varepsilon}$-NTU Method,' Chem. Eng. Prog. Symp. Series, Vol. 62, No. 64, pp. 185-196

Raju, K. S. N., Bansal, J. C., 1983, 'Design of Plate Heat Exchangers, ' in: Low Reynolds Number Flow Heat Exchangers, S. Kakac, R. K. Shah, and A. E. Bergles, eds., pp. 899-912

Cooper, A., 1974, 'Recover more Heat with Plate Heat Exchangers,' The Chemical Engineer, Vol. 259, No. 1, pp. 280-285

Kandlikar, S. G., Shah, R. K., 1989, 'Multipass Plate Heat Exchangers- Effectiveness NTU Results and Guidelines for Selecting Pass Arrangements,' ASME J. of Heat Transfer, Vol. III, pp. 300-313

Bogaert, R., Bolcs, A., 1995, 'Global Performance of a Prototype Brazed Plate Heat Exchanger in a Large Reynolds Number Range,' Experimental Heat Transfer, Taylor & Frances, No. 8, pp. 293-311

Stasiek, J., Collins, M. W., Clofalo, M., and Chew, P. E., 1996, 'Investigation of Flow and Heat Transfer in corrugated Passages-Ⅰ Experimental Results,' Int. J. Heat Mass Transfer, Vol. 39, No. 1, pp. 149-164 crossref(new window)

전창덕, 정재원, 이진호, 강신형, 1999, '자동차 응축기용 다채널관의 압력강하 특성에 관한 연구,' 대한기계학회논문집 B권, 제23권, 제7호, pp. 881-892

Edwards, M. F., 1974, 'Heat Transfer and Pressure Drop Characteristics of a Plate Heat Exchanger Using Newtonian and Non-Newtonian Liquids,' The Chemical Engineer, Vol. 259, No. 1, pp. 286-288

전창덕, 정재원, 이진호, 1999, '자동차용 다채널관의 응축 열전달에 관한 연구,' 대한기계학회논문집 B권, 제23권, 제4호, pp. 479-491

Breber, G., Palen, J. W., and Taborek, J., 1980, 'Prediction of Horizontal Tubeside Condensation of Pure Components Using Flow Regime Criteria,' J. of Heat Transfer, Vol. 102, pp. 471-476

Lockhart, R. W., and Martinelli, R. C., 1949, 'Proposed Correlation of Data for Isothermal Two-Phase, Two-Components Flow in Pipes,' Chem. Eng. Prog., Vol. 45, No. 1, p. 39

Traviss, D. P., Rohsenow, W. M., and Baron, A. B., 1972, 'Forced - Convection Condensation inside Tube : A Heat Transfer Equation for Condenser Design,' ASHRAE Trans, Vol. 79, pp. 157-165

Azer, N. Z., Abis, L. V., and Soliman, H. M., 1988, 'Local Heat Transfer Coefficients during Annular Flow Condensation,' ASHRAE No. 2247, pp. 135-143

Haraguchi, H., Koyama, S., Fujii, T., 1994, Condensation of Refrigerant HCFC-22,HFC-134a and HCFC-123 in a Horizontal Smooth Tube,' 일본기계학회논문집, Vol. 60, No. 574, pp. 239-252

Akers, W. W., Deans, H. A., and Crosser, O. K., 1959, 'Condensation Heat Transfer within Horizontal Tubes,' Chemical Engineer Progress Symposium Series, Vol. 55, pp. 171-176

Shah, M. M., 1979, 'A General Correlation for Heat Transfer During Film Condensation Inside Pipes,' Int. J. Heat Mass Transfer, Vol. 22, pp. 547-556 crossref(new window)