Heat Transfer Enhancement by the Perforated Plate of Round Impinging Air Jets

Title & Authors
Heat Transfer Enhancement by the Perforated Plate of Round Impinging Air Jets
Kim, Yun-Taek; Lee, Yeong-Min; Won, Se-Yeol; Lee, Dae-Hui;

Abstract
The purpose of this study is to investigate the heat transfer augmentation using the perforated plate placed in front of a target plate in an axisymmetric impinging air jet system. The new liquid crystal technique using neural networks with median filtering is used to determine the Nusselt number distributions on the target surface. The experiments were made for the jet Reynolds number (Re) 23,000. The effects of the pitch-to-diameter (p/d1) from 1.5 to 2.5 in the perforated plate, the hole diameter on perforated plate (d1) from 4㎜ to 12㎜, the perforated plate to target surface distance (z/d1) from 1 to 3, and the nozzle-to-target surface distance (L/d) from 2 to 10 on the heat transfer characteristics were experimentally investigated. It was found that when the perforated plate was located between the nozzle exit and the target plate, the average heat transfer rate at the stagnation region corresponding to r/d$\small{\leq}$1.0 was increased up to the maximum 2.3 times compared to the case without the perforated plate.
Keywords
Round Impinging Jet;Perforated Plate;Gold Film Intrex;Liquid Crystal;Neural Networks and Median Filtering;
Language
Korean
Cited by
References
1.
Martin, H., 1997, 'Heat and Mass Transfer between Impinging Gas Jets and Solid Surfaces,' Advances in Heat Transfer, Academic Press, New York, Vol. 13, pp. 1-60

2.
Down, S. J. and James, E. H., 1987, 'Jet Impinging Heat Transfer-A Literature Survey,' ASME paper No. 87-H-35

3.
Goldstein, R. J., Behbahani, A. I. and Heppelmann, K. K., 1986, 'Streamwise Distribution of the Recovery Factor and The Local Heat Transfer Coefficient to an Impinging Circular Air Jet,' Int. J. Heat Mass Transfer, Vol. 29, No. 8, pp. 1227-1235

4.
Viskanta, R., 1993, 'Heat Transfer to Impinging Isothermal Gas and Frame Jet,' Experimental Thermal and Fluid Science, Vol. 6, pp. 111-134

5.
Kurima, J., Miyamoto, M. and Harada, T., 1989, 'Heat Transfer Augmentation of an Axisymmetric Impinging Jet Using a Perforated Plate Set in front of a Target Plate,' Heat Transfer Japanese Research, Vol. 18, No. 6, pp. 1-20

6.
Goldstein, R. J., and Timmers, J. F., 1982, 'Visualization of Heat Transfer from Arrays of Impinging Jets,' International Journal of Heat and Mass Transfer, Vol. 25, No. 12, pp. 1857-1868

7.
Ali Khan, M. M., Hirata, M., Kasagi, N., and Nishiwaki, N., 1982, 'Heat Transfer Augmentation in an Axisymmetric Impinging Jet,' The Seventh International Heat Transfer Conference, Vol. 3, pp. 363-368

8.
Behbahani, A. I. and Goldstein, R. J., 1983, 'Local Heat Transfer to Staggered Arrays of Impinging Circular Air Jets,' Journal of Engineering for Power, Vol. 105, pp. 335-360

9.
Kercher, D. M., and Tabakoff, W., 1970, 'Heat Transfer by a Square Array of Round Air Jets Impinging Perpendicular to a Flat Surface Including the Effect of Spent Air,' Journal of Engineering for Power, January, pp. 73-82

10.
Hollworth, B. R., and Berry, R. D., 1978, 'Heat Transfer from Arrays of Impinging Jets with Large Jet-to-Jet Spacing,' Journal of Heat Transfer, Vol. 100, pp. 353-357

11.
Florschuetz, L. W., Metzer, D. E., and Su, C. C., 1984, 'Heat Transfer Characteristics for Jet Array Impingement with Initial Crossflow,' Journal of Heat Transfer, Vol. 106, pp. 34-41

12.
Florschuetz, L. W., and Su, C. C., 1987, 'Effect of Crossflow Within an Array of Impinging Jets,' Journal of Heat Transfer, Vol. 109, pp. 74-82

13.
Van Treuren, K. W., Wang, Z., Ireland, P. T., and Jones, T. V., 1994, 'Detailed Measurements of Local Heat Transfer coefficient and Adiabatic Wall Temperature Beneath an Array of Impinging Jets,' Journal of Turbomachinery, Vol. 116, pp. 369-374

14.
Huber, A. M., and Viskanta, R., 1994, 'Convective Heat Transfer to a Confined Impinging Array of Air Jets with Spent Air Exits,' Journal of Heat Transfer, Vol. 116, pp. 570-576

15.
Chang, C. T., Kojasoy, G., Landis, F., and Downing, S., 1995, 'Confined Single and Multiple Jet Impingement Heat Transfer-1. turbulent Submerged Liquid Jets,' International Journal of Heat and Mass Transfer, Vol. 38, No. 5, pp. 833-842

16.
Huang, Y., Srinath, V. E., and Han, J. C., 1996, 'Local Heat Transfer Coefficient Distribution under an Array of Impinging Jets Using a Transient Liquid Crystal Technique,' Proceedings of the 6th International symposium on Transport Phenomena and Dynamics of Rotating Machinery, Vol. 2, pp. 553-562

17.
Guo, T., Zhu, T., Hu, J., and Gong, L., 1996, 'The Effect of the Geometric Parameters of a Perforated Plate on its Heat Transfer Characteristics,' Cryogenics, Vol. 36, No. 6, pp. 443-446

18.
Jorge, M. M. Barata, 1996, 'Fountain Flows Produced by Multiple Impinging Jets in a Crossflow,' American Institute of Aeronautics and Aeronautics Journal, Vol. 34, No. 12, pp. 2523-2530

19.
이대희, 부광석, 원세열, 정재훈, 김윤택, 1999, '미디안 필터와 신경회로망을 이용한 향상된 액정교정 기술개발 및 열전달 연구에의 응용,' 대한기계학회 춘계학술대회 논문집 B, pp. 915-920

20.
Lee, D. H., Chung, Y. S., and Kim, D. S., 1997, 'Turbulent Flow and Heat Transfer Measurements on a Curved Surface with a Fully Developed Round Impinging Jet,' International Journal of Heat and Fluid Flow, Vol. 18, No. 1, pp. 160-169

21.
Baughn, J. W., Ireland, P. T., Jones, T. V., and Saniei, N., 1989, 'A Comparison of the Transient and Heated-Coating Methods for the Measurements of the Local Heat Transfer Coefficients on a Pin Fin,' ASME Journal of Heat Transfer, Vol. 111, pp. 877-881

22.
Kline, S. J., and Mcklintock, F. A., 1953, 'Describing Uncertainties in Single Sample Experiments,' Mechanical Engineering, Vol. 75, pp. 3-8

23.
이대희, 원세열, 이영민, 조헌노, 박성은, 1998, '원형 충돌제트의 노즐 직경이 열전달에 미치는 영향,' 대한기계학회 98년도 열공학부문 학술대회 논문집, pp. 71-75