Advanced SearchSearch Tips
Effect of Heating Rates on Microstructures in Brazing Joints of STS304 Compact Heat Exchanger using MBF 20
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
  • Journal title : Journal of Welding and Joining
  • Volume 34, Issue 2,  2016, pp.46-53
  • Publisher : The Korean Welding and Joining Society
  • DOI : 10.5781/JWJ.2016.34.2.46
 Title & Authors
Effect of Heating Rates on Microstructures in Brazing Joints of STS304 Compact Heat Exchanger using MBF 20
Kim, Jun-Tae; Heo, Hoe-jun; Kim, Hyeon-Jun; Kang, Chung-Yun;
  PDF(new window)
Effect of heating rate on microstructure of brazed joints with STS 304 Printed Circuit Heat Exchanger (PCHE),which was manufactured as large-scale(, mm), have been studied to compare bonding phenomenon. The specimens using MBF 20 was bonded at for 1hr with and heating rate, respectively. In case of a heating rate of , overflow of filler metal was observed at the edge of a brazed joints showing the height of filler metal was decreased from to . At the center of the joints, CrB and high Ni contents of -Ni was existed. For the joints brazed at a heating rate of , the height of filler was decreased from to showing the overflow of filler was not appeared. At the center of the joints, only -Ni was detected gradating the Ni contents from center. This phenomenon was driven from a diffusion amount of Boron in filler metal. With a fast heating rate , diffusion amount of B was so small that liquid state of filler metal and base metal were reacted. But, for a slow heating rate , solid state of filler metal due to low diffusion amount of B reacted with base metal as a solid diffusion bonding.
PCHE (Pring cicuit heat exchanger);Brazing;MBF 20;Boron diffusion;Microstructure;
 Cited by
순 티타늄 박판의 파이버 레이저 용접시 결함 억제를 위한 연속의 출력 파형제어 특성(II) - 중첩부 길이변화에 따른 영향 -,김종도;김지성;

Journal of Welding and Joining, 2016. vol.34. 6, pp.69-74 crossref(new window)
Ae-Jeong Jeon et al., J. Welding and Jopining, 32(4) (2014), 384-392 (in Korean)

Li, Qi, et al., RENEW SUST ENERG REV, 15(9) (2011), 4855-4875 crossref(new window)

Takeda Takeshi, et al., NUCL ENG DES, 168(1) (1997), 11-21 crossref(new window)

조흥곤, 기계산업 452 단일호 (2015), 64-72 (in Korean)

Sabharwall Piyush, et al., J. Thermal Sci. Eng. Appl., 5(1) (2013), 011009 crossref(new window)

Jiang, Wenchun, Jianming Gong, and Shan-Tung Tu., MATER DESIGN, 31(1) (2010), 648-653 crossref(new window)

Jeong-Woo Yu, et al., Journal of KWJS, 30(6) (2012), 106-112 (in Korean)

Ngo, Tri Lam, et al., EXP THERM FLUID SCI, 30(8) (2006), 811-819 crossref(new window)

Nikitin, Konstantin, Yasuyoshi Kato, and Lam Ngo., INT J REFRIG, 29(5) (2006), 807-814 crossref(new window)

Gale, W. F. and D. A. Butts., SCI TECHNOL WELD JOI, 9(4) (2004), 283-300. crossref(new window)

Yong-Won Lee and Jong-Hoon Kim., Korean Journal of Materials Research, 17(3) (2007), 179-183 crossref(new window)

Chung-Yun Kang, et al., Journal of KWS, 17(2) (1999), 1-8 (in Korean)

Chung-Yun Kang, et al., Journal of KWS, 21(3) (2003), 21-3 (in Korean)

J. Lemus-Ruiiz et al., J MATER PROCESS TECH, 223 (2015), 16-21 crossref(new window)

Wenchun Jiang, Jianming Gong, MATER DESIGN, 32(2) (2011), 736-742 crossref(new window)

R K Roy, H Bapari, A K Panda, A Mitra, SCI TECHNOL WELD JOI, 18(3) (2013), 216-221 crossref(new window)

Ruiz-Vargas, J, et al., J MATER PROCESS TECH, 213(1) (2013), 20-29 crossref(new window)