Design and Implementation of a Reverse Matrix Converter for Permanent Magnet Synchronous Motor Drives

- Journal title : Journal of Electrical Engineering and Technology
- Volume 10, Issue 6, 2015, pp.2297-2306
- Publisher : The Korean Institute of Electrical Engineers
- DOI : 10.5370/JEET.2015.10.6.2297

Title & Authors

Design and Implementation of a Reverse Matrix Converter for Permanent Magnet Synchronous Motor Drives

Lee, Eunsil; Lee, Kyo-Beum;

Lee, Eunsil; Lee, Kyo-Beum;

Abstract

This paper presents the development of a system with a reverse matrix converter (RMC) for permanent magnet synchronous motor (PMSM) drive and its effective control method. The voltage transfer ratio of the general matrix converter is restricted to a maximum value of 0.866, which is not suitable for applications whose source voltages are lower than the load voltages. The proposed RMC topology can step up the voltage without any additional components in the conventional circuit. Its control method is different from traditional matrix converter’s one, thus this paper proposes control schemes of RMC by means of controlling both the generator and motor side currents with properly designed control loop. The converter can have sinusoidal input/output current waveforms in steady state condition as well as a boosted voltage. In this paper, a hardware system with an RMC for a PMSM drive system is described. The performance of the system was investigated through experiments

Keywords

Reverse matrix converter;Permanent magnet synchronous motor;Step-up voltage;Voltage transfer ratio;AC-AC converter;

Language

English

Cited by

References

1.

T. Friedli, J. W. Kolar, J. Rodriguez, and P. W. Wheeler, “Comparative evaluation of three-phase ac-ac matrix converter and voltage dc-link back to-back converter systems,” IEEE Trans. Ind. Electron., vol. 59, no. 12, pp. 4487-4510, Dec. 2012.

2.

J. W. Kolar, T. Friedli, J. Rodriguez, and P. W. Wheeler, “Review of three-phase PWM ac-ac converter topologies,” IEEE Trans. Ind. Electron. — Special Section Matrix Converters, vol. 58, no. 11, pp. 4988-5006, Nov. 2011.

3.

P. Szcześniak, “Three-phase AC-AC power converters based on matrix converter topology,” Springer, 2013.

4.

P. Nielsen, "The matrix converter for an induction motor drive," Ph.D. Thesis, Aalborg University, Denmark, 1996.

5.

K. Iimori, K. Shinohara, O. Tarumi, Z. Fu, and M. Muroya, “New current-controlled PWM rectifier-voltage source inverter without DC link components,” in Proc. PCC, pp. 783-786, 1997.

6.

J.W. Kolar, F. Schafmeister, S. D. Round, and H. Ertl, “Novel three-phase ac-ac sparse matrix converters,” IEEE Trans. Power Electron., vol. 22, no. 5, pp. 1649-1661, Sep. 2007.

7.

L.Wei, T. A. Lipo, and H.Chan, “Matrix converter topologies with reduced number of switches,” in Proc. PESC., vol. 1, pp. 57-63, 2002.

8.

Y. Bak, E. Lee, and K. B. Lee, “An indirect matrix converter for dual output AC drive system with reduced number of power transistors,” in Proc. CENCON, pp. 360-364, 2014.

9.

X. Liu, P. Wang, P. C. Loh, and F. Blaabjerg, “A compact three-phase single-input/dual-output matrix converter,” IEEE Trans. Ind. Electron., vol. 59, no. 1, pp. 6-16, Jan. 2012.

10.

T. Wijekoon, C. Klumpner, P. Zanchetta, and P. W. Wheeler, “Implementation of a hybrid AC-AC direct power converter with unity voltage transfer,” IEEE Trans. Power Electron., vol. 23, no. 4, pp. 1918-1926, Jul. 2008.

11.

K. Park, K. B. Lee, and F. Blaabjerg, “Improving output performance of a Z-source sparse matrix converter under unbalanced input-voltage conditions,” IEEE Trans. Power Electron., vol. 27, no. 4, pp. 2043-2054, Apr. 2012.

12.

B. Ge, Q. Lei, W. Qian, and F. Z. Peng, “A family of Z-source matrix converters,” IEEE Trans. Ind. Electron., vol. 59, no. 1, pp. 35-46, Jan. 2012.

13.

X. Liu, P. C. Loh, P. Wang, F. Blaabjerg, Y. Tang, and E. A. Al-Ammar, “Distributed generation using indirect matrix converter in reverse power mode,” IEEE Trans. Power Electron., vol. 28, no. 3, pp. 1072-1082, Mar. 2013.

14.

X. Liu, P. Wang, P. C. Loh, and F. Blaabjerg, “Distributed generation interface using indirect matrix converter in boost mode with controllable grid side reactive power,” in Proc. IPEC, pp. 59-64, 2012.

15.

Z. Fedyczak, G. Tadra, and M. Klytta, “Implementation of the current source matrix converter with space vector modulation,” in Proc. EPE/PEMC, pp. T2-97-T2-102, 2010.

16.

K. Park and K. -B. Lee, “Hardware Simulator Development for a 3-Parallel Grid-connected PMSG Wind Power System,” J. of Power Electron., vol. 10, no. 5, pp. 555-562, Sept. 2010.

17.

A.K. Sahoo, K. Basu, N. Mohan, “Systematic Input Filter Design of Matrix Converter by Analytical Estimation of RMS Current Ripple,” IEEE Trans. Industrial Electronics, vol. 62, no. 1, pp. 132-143, 2015.

18.

C. Klumpner “An indirect matrix converter with a cost effective protection and control”, in Proc. EPE, pp.1-11 2005.

19.

M. Aner, N. Benaifa, E. Nowicki, “A PMSM drive design with inverter-stage soft switching hysteresis current control and space vector modulation for two-level operation of a very sparse matrix converter,” In Proc. EPEC, pp. 22-23, 2009.