Performance Analysis and Optimal Design of Heat Exchangers Used in High Temperature and High Pressure System

- Journal title : International Journal of Aeronautical and Space Sciences
- Volume 11, Issue 1, 2010, pp.19-25
- Publisher : The Korean Society for Aeronautical & Space Sciences
- DOI : 10.5139/IJASS.2010.11.1.019

Title & Authors

Performance Analysis and Optimal Design of Heat Exchangers Used in High Temperature and High Pressure System

Kim, Yang-Gu; Choi, Byoung-Ik; Kim, Kui-Soon; Jeong, Ji-Hwan;

Kim, Yang-Gu; Choi, Byoung-Ik; Kim, Kui-Soon; Jeong, Ji-Hwan;

Abstract

A computational study for the optimal design of heat exchangers (HX) used in a high temperature and high pressure system is presented. Two types of air to air HX are considered in this study. One is a single-pass cross-flow type with straight plain tubes and the other is a two-pass cross-counter flow type with plain U-tubes. These two types of HX have the staggered arrangement of tubes. The design models are formulated using the number of transfer units (-NTU method) and optimized using a genetic algorithm. In order to design compact light weight HX with the minimum pressure loss and the maximum heat exchange rate, the weight of HX core is chosen as the object function. Dimensions and tube pitch ratio of a HX are used as design variables. Demanded performance such as the pressure loss () and the temperature drop () are used as constraints. The performance of HX is discussed and their optimal designs are presented with an investigation of the effect of design variables and constraints.

Keywords

Heat exchanger;Optimal design;

Language

English

Cited by

References

1.

Jeong, J. H., Kim, L. S., Ha, M. Y., Lee, J. K., Kim, K. S., and Ahn, Y. C., 2007, "Review of Heat Exchanger Studies for High-Efficiency Gas Turbines", ASME Turbo Expo 2007, GT2007-28071.

2.

McDonald C. F. and Wilson, D. G.., 1996, "The Utilization of Recuperated and Regenerated Engine Cycles for High-Efficiency Gas Turbine Engines in the 21st Century", Applied Thermal Engineering, 16, pp. 635-653.

3.

Yakinthos, K., Missirlis, D., Palikaras, A., Storm, P., Simon, B., and Goulas, A., 2007, "Optimization of the Design of Recuperative Heat Exchangers in the Exhaust Nozzle of an Aero Engine", Applied Mathematical Modeling, 31, pp. 2524-2541.

4.

Schoenenborn, H., Elbert, E., Simon, B. and Storm, P., 2006, "Thermomechanical Design of a Heat exchanger for a Recuperative Aeroengine", International J. of Heat and Mass Transfer, 128, 736-744.

5.

Kasagi, N., Suzuki, Y., Shakzono N. and Oku, T., 2003, "Optimal Design and Assessment of High Performance Micro Bare-Tube Heat Exchangers", 4th Int. Conf. on Compact Heat Exchangers and Enhancement Technologies for the Process Industries, pp. 241-246.

6.

Boggia, S., Rud, K., 2005, "Intercooled Recuperated Gas Turbine Engine Concept", AIAA 2005-4192.

7.

Hausen, H., Darstellung des Warmeuberganges in Rohren durch verallgemeinerte Potenzbeziehungen, Z. Ver. Dtsch. Ing., Beiheft Verfahrenstech., No. 4, pp. 91-134, 1943.

8.

Filonenko, G. K., Hydraulic Resistance in Pipes, Teploenergetika, vol. 1, pp. 40-44

9.

Zukauskas, A. A., Makarevivius, V. J., and Slanciauskas, A. A., "Heat Transfer in Banks of Tubes in Crossflow of Fluid", Thermophysics 1, pp. 47-68, Mintis, Vilnius, 1968.

10.

Kays, W. M., 1950, "Loss Coefficients for Abrupt Changes in Flow Cross Section with Low Reynolds Number Flow in Single and Multiple Tube System", Trans. ASME, vol. 72, pp. 1067-1074, 1950.

11.

Moshfeghian, M and Bell, K. J., 1979. "Local heat transfer measurements in and downstream from a U-bend", ASME paper No. 79-HT-82.

13.

Jaluria, Y., 2008, Design and Optimization of Thermal Systems, CRC Press, pp.444-445.