Plasticity and Fracture Behaviors of Marine Structural Steel, Part IV: Experimental Study on Mechanical Properties at Elevated Temperatures

Title & Authors
Plasticity and Fracture Behaviors of Marine Structural Steel, Part IV: Experimental Study on Mechanical Properties at Elevated Temperatures
Choung, Joon-Mo; Im, Sung-Woo; Park, Ro-Sik;

Abstract
This is the fourth of a series of companion papers dealing with the mechanical property reductions of various marine structural steels. Even though a reduction of the elastic modulus according to temperature increases has not been obtained from experiments, high temperature experiments from room temperature to $\small{900^{\circ}C}$ revealed that initial the yield strength and tensile strength are both seriously degraded. The mechanical properties obtained from high temperature experiments are compared with those from EC3 (Eurocode 3). It is found that the high temperature test results generally comply with the prediction values by EC3. Based on the prediction of EC3, time domain nonlinear finite element analyses were carried out for a blast wall installed on a real FPSO. After applying the reduced mechanical properties, corresponding to $\small{600^{\circ}C}$ to the FE model of the blast wall, more than three times the deflections were observed and it was observed that most structural parts experience plastic deformations exceeding the reduced yield strength at the high temperature. It is noted that a protection facility such as PFP (passive fire protection) should be required for structures likely to be directly exposed to fire and explosion accident.
Keywords
initial yield strength;tensile strength;elastic modulus;reduction factor;elevated temperature;high transition temperature;blast wall;
Language
Korean
Cited by
1.
조선 해양 구조물용 강재의 소성 및 파단 특성 V: 온도 의존성을 고려한 변형률 속도에 관한 실험적 연구,정준모;임성우;김경수;

한국해양공학회지, 2011. vol.25. 3, pp.73-84
References
1.
American Society for Testing and Materials (ASTM) (2004). E 8 - 04 Standard Test Methods for Tension Testing of Metallic Materials.

2.
American Petroleum Institute (API) (2006). Recommended Practice 2FB: Design of Offshore Facilities Against Fire and Blast Loading.

3.
Bao, Y. and Wierzbicki, T. (2004). "On Fracture Locus in the Equivalent Strain and Stress Triaxiality Space", International Journal of Mechanical Sciences, Vol 46, pp 81-98.

4.
British Standard (BS) (1990). BS 5950: Part 8. Code of practice for fire resistance design.

5.
Choung, J. (2009). "Comparative Studies of Fracture Models for Marine Structural Steels", Ocean Engineering, Vol 36, pp 1164-1174.

6.
Choung, J., Shim, C.S. and Kim, K.S. (2011a). "Plasticity and Fracture Behaviors of a Marine Structural Steel, Part I: Technical Backgrounds of Strain Hardening and Rate Hardening", Journal of Ocean Engineering and Technology (to be published).

7.
Choung, J., Shim, C.S. and Kim, K.S. (2011b). "Plasticity and Fracture Behaviors of a Marine Structural Steel, Part II: Theoretical Backgrounds of Fracture", Journal of Ocean Engineering and Technology (to be published).

8.
Choung, J., Shim, C.S. and Kim, K.S. (2011c). Plasticity and Fracture Behaviors of a Marine Structural Steel, Part III: Experimental Study on Failure Strain (to be published).

9.
European Committee for Standardisation (CEN) (1995). Eurocode 3: Design of steel structures. Part 1-2: General rules - Structural fire design (EN 1993-2-1). Brussels, Belgium. CEN

10.
Fire and Blast Information Group (FABIG) (1993). Technical Note on Fire Resistant Design of Offshore Topside Structures. FABIG.

11.
Health and Safety Executive (2001). Offshore Technology Report OTO 2001/020-Elevated Temperature and High Strain Rate Properties of Offshore Steels.

12.
Nemat-Nasser, S. and Guo, W.G. (2003). "Thermomechanical Response of DH-36 Structural Steel over a Wide Range of Strain Rates and Temperature", Mech. Mat., Vol 35, pp 1023-1047.

13.
The Steel Construction Institute (SCI) (1992). Interim Guidance Notes for the Design and Protection of Topside Structures against Explosion and Fire. SCI