Advanced SearchSearch Tips
Evaluation of the Corrosion Property on the Welded Zone of Cast Steel Piston Crown with Types of Electrode
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Evaluation of the Corrosion Property on the Welded Zone of Cast Steel Piston Crown with Types of Electrode
Moon, Kyung-Man; Kim, Yun-Hae; Lee, Myeong-Hoon; Baek, Tae-Sil; Kim, Jin-Gyeong;
  PDF(new window)
Wear and corrosion of the engine parts surrounded with combustion chamber is more serious compared to the other parts of the engine because temperature of the exhaust gas in a combustion chamber is getting higher and higher with increasing of using the heavy oil of low quality. Therefore, an optimum repair weldment as well as an available choice of the base metal for these parts are very important to prolong their lifetime in a economical point of view. It reported that there was an experimental result for repair weldment on the forged steel which would be generally used with piston crown material, however, it is considered that there is no study for the repair weldment on the cast steel of piston crown material. In this study, four types of electrodes such as 1.25Cr-0.5Mo, 0.5Mo Inconel 625 and 718 were welded with SMAW and GTAW methods on the cast steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected zone and base metal were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% solution. In the cases of Inconel 625, 718, the weld metals and base metals exhibited the best and worst corrosion resistance respectively, however, 1.25Cr-0.5Mo and 0.5Mo indicated that corrosion resistance of the base metal was better than the weld metal. And the weld metal welded with electrodes of Inconel 625 revealed the best corrosion resistance among the electrodes, and Inconel 718 followed the Inconel 625. Hardness relatively also indicated higher value in the weld metal compared to heat affected zone and base metal. In particular, Inconel 718 indicated the highest value of hardness compared to other electrodes in the heat affected zone.
Corrosion Potential;Galvanic Cell;Weld Metal;Heat Affected Zone;Arc Welding;
 Cited by
피스톤 크라운용 단강에 인코넬 718 용접재료로 용접된 용접부의 특성 평가,이성열;문경만;정재현;이명훈;백태실;

한국해양공학회지, 2016. vol.30. 4, pp.334-340 crossref(new window)
Evaluation of Characteristics of Welding Zones Welded with Inconel 718 Filler Metal to Piston Crown Forged Material, Journal of Ocean Engineering and Technology, 2016, 30, 4, 334  crossref(new windwow)
Ahn, S.H., Jeong, J.H., Nam, K.W., 2005. Evaluation of Characteristic for SS400 and STS304 steel by Weld Thermal Cycle Simulation. Journal of Ocean Engineering and Technology, 19(4), 64-71.

Bilmes, P.D., Liorente, C.L., Saire Huaman, Gassa L.M., Gervasi, C.A., 2006. Microstructure and Pitting Corrosion of 13CrNiMo Weld Metal. Corrosion Science, 48, 3261-3270. crossref(new window)

Jeon, D.H., 1985. Control of the Corrosion and Anti-corrosion. Iljoongsha, 426-428.

Jones, D.A., 1998. Principles and Prevention of Corrosion. Original American Edition Published by Prentice-Hall, Inc., 314.

Kim, J.G., Kang, M.S., Kim, Y.S., 2006. A Study on Characteristics of Repair Welding for Cast Iron Part of Diesel Engine for Ship. Journal of Ocean Engineering and Technology, 20(2), 41-45.

Kim, M.N., Kim, B.I., Han, J.D., 2000. A Study of Mechanical Properties of Underwater Wet Welding Electrode. Journal of Ocean Engineering and Technology, 14(4), 56-61.

Moon, K.M., 1999. Practical Electro - Chemistry. Hyosung Publishing Co., 177.

Moon, K.M., Lee, M.H., Kim, K.J., Kim, J.G. Kim, S.J., 2003. A Study on the Post-Weld Heat Treatment Effect to Mechanical Properties and Hydrogen Embrittlement for Heating Affected Zone of a RE36 Steel. Corrosion Science and Technology, 2(6), 283-288.

Muylder, J.V., Pourbaix, M., 1966. Atlas of Electrochemical Equilibria in Aqueous Solution. Ed. by M. Pourbaix, Rergomon Press and Cebelcor, 260-509.

Shin, M.K., 1984. New Edition Workshop Practice. Ah Sung Publishing Co., 244-245.

Tsay, L.W., Lin, W.L., Chenct S.W., Leu G.S., 1997. Hydrogen Sulphide Stress Corrosion Cracking of 2.25 Cr-Mo Steel Weldments. Corrosion Science, 39(7), 1165-1176. crossref(new window)