JOURNAL BROWSE
Search
Advanced SearchSearch Tips
Experimental Study on Correction of Thermal Conductivity Obtained by Heat Flow Method using Commercial Guarded Hot Plate Method Apparatus
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Experimental Study on Correction of Thermal Conductivity Obtained by Heat Flow Method using Commercial Guarded Hot Plate Method Apparatus
Lee, Jin-Sung; Kim, Kyung-Su; Kim, Yooil; Woo, Suck-Min; Yun, Seungjin;
  PDF(new window)
 Abstract
This paper addresses experimental methodologies to measure the temperature-dependent thermal conductivity of the insulation materials popularly used for LNG cargo containment systems. The measurement techniques considered in this paper are the guarded hot plate (GHP) method and heat flow method (HFM). The former is based on the power supplied to the hot plate to keep the temperature constant, and the latter is based on a direct heat flux measurement. In order to improve the accuracy of the HFM, the thermal conductivity obtained by GHP was cross-compared with the HFM results, and a calibration factor was derived. It was found that the thermal conductivities measured by the two methods corresponded well under room temperature, but the deviation tended to slightly increase as the temperature decreased. Because of the easy installation and operability of HFM, it can be used to measure thermal conductivity in a large scale mock-up test or unit insulation panel test, where the GHP method is difficult to apply.
 Keywords
Heat flow method;Guarded hot plate method;Heat flux sensor;Sensitivity;Thermal conductivity;
 Language
Korean
 Cited by
 References
1.
ASTM, 2004. Standard Test Method for Steady-State Thermal Transmission Properties by Mean of the Heat Flow Meter Apparatus. American Society for Testing and Materials, ASTM C518-02.

2.
Bomberg, M., Solvason, K.R., 1983. Comments on Calibration and Design of a Heat Flow Meter. American Society for Testing and Materials(ASTM), STP 789, 277-292.

3.
Jang, C.W., Shim, C.S., Song, H.C., Song, C.Y., 2013. Study on Cryogenic Behavior of Reinforced Polyurethane Foam for Membrane Type LNG Carrier. Journal of Ocean Engineering and Technology, 27(1), 74-79. crossref(new window)

4.
Kim, B.S., Kim, J.H., Kim Y.J., Cho, H.H., 2005. Fabrication and Calibration of Micro Heat Flux Sensor for Heat Flux Measurement. Proceedings of KSME 2005 Autumn Annual Meeting, Yongpyeong Korea, 195-199.

5.
Kim, J.G., Kim, Y.M., Kim, C.S., 1997. A Study on Unsteady Temperature Distribution Analysis of Moss Type LNG Carrier by Insulation System. Journal of Ocean Engineering and Technology, 11(4), 159-168.

6.
Lee, J.H., Kim, Y.J., Hwang, S.Y., 2014. Numerical Model of Heat Diffusion and Evaporation by LNG Leakage at Membrane Insulation. Journal of Ocean Engineeing and Technology, 28(6), 517-526. crossref(new window)

7.
Lee, J.S., Kim, K.S., Kim, Y.I., Yoo, C.H., Park, J.I., Kang, B.H., 2014. Fatigue Strength Assessment of High Manganese Steel for LNG CCS. Journal of the Society of Naval Architects of Korea, 51(3), 246-253. crossref(new window)

8.
Lee, J.S., Kim, K.S., Kim, Y.I., Yoo, C.H., You, W.H., 2013. An Experimental Study on Fatigue Performance of Cryogenic metallic materials for IMO type B tank. International Journal of Naval Architecture and Ocean Engineering, 5(4), 580-597.

9.
Netzsch, 2014. Heat Flow Meter. [Online] (Updated February 2014) Available at: [Accessed October 2014].

10.
Sensormag, 1999, Heat flux Sensors. [Online] (Updated January 1999) Available at: [Accessed October 2014].

11.
Han, K.C., Hwang, S.W., Cho, J.R., Kim, J.S., Yoon, J.W., Lim, O.K., Lee, S.B., 2011. Astudy on the Boil-Off Rate Prediction of LNG Cargo Containment Filled with Insulation Powders. Journal of the Computational Structural Engineering Institute of Korea, 24(2), 193-200.

12.
Haruyama, T., 2001. Performance of Peltier Elements as a Cryogenic Heat Flux Sensor at Temperatures down to 60K. Cryogenics, 41, 335-339. crossref(new window)

13.
University of Saskatchewan, 2005. Thermal Conductivity and Resistance. [Online] (Updated July 2005) Available at: [Accessed October 2014].

14.
Yang, H.C., Song, C.H., Kim, M.H., 2004. Development of Micro-machined Heat Flux Sensor by Using MEMS Technology. Proceedings of KSME 2004 Spring Annual Meeting, Pyeong-chang Korea, 1364-1369.