JOURNAL BROWSE
Search
Advanced SearchSearch Tips
Effects of Heat Input and Preheat/interpass Temperature on Strength and Impact Toughness of Multipass Welded Low Alloy Steel Weld Metal
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Effects of Heat Input and Preheat/interpass Temperature on Strength and Impact Toughness of Multipass Welded Low Alloy Steel Weld Metal
Bang, Kook-soo; Jung, Ho-shin; Park, Chan;
  PDF(new window)
 Abstract
The effects of the heat input and preheat/interpass temperatures on the tensile strength and impact toughness of multipass welded weld metal were investigated and interpreted in terms of the recovery of the alloying elements and microstructure. Increases in both the heat input and preheat/interpass temperatures decreased the tensile strength of the weld metal. A lower recovery of alloying elements, especially Mn and Si, and smaller area fraction of acicular ferrite in the weld metal were observed in higher heat input welding, resulting in a lower tensile strength. In contrast, only a microstructure difference was observed at a higher preheat/interpass temperature. The impact toughness of the weld metal gradually increased with an increase in the heat input because of the lower tensile strength. However, it decreased again when the heat input was larger than 45 kJ/cm because of the much smaller area fraction of acicular ferrite. No effect of the preheat/interpass temperature on the impact toughness was observed. The formation of a weld metal heat-affect zone showed little effect on the impact toughness of the weld metal in this experiment.
 Keywords
Strength;Toughness;Heat input;Preheat/interpass temperature;
 Language
Korean
 Cited by
 References
1.
Bang, K.-S., Jung, D.-H., Park, C., Chang, W.-S., 2008. Effects of Welding Parameters on Tensile Strength of Weld Metal in Flux Cored Arc Welding. Science and Technology of Welding and Joining, 13(6), 509-514. crossref(new window)

2.
Byun, J.-C., Bang, K.-S., Chang, W.-S., Park, C.-G., Chung, W.-H., 2006. Effects of Heat Input and Interpass Temperature on the Strength and Impact Toughness of Multipass Weld Metal in 570MPa Grade Steel. Journal of Korean Welding and Joining Society, 24(1), 64-69 (in Korean).

3.
Dixon, B., Hakansson, K., 1995. Effects of Welding Parameters on Weld Zone Toughness and Hardness in 690MPa Steel. Welding Journal, 74(4), 122s-132s.

4.
Evans, G.M., 1982. The Effect of Heat Input on the Microstructure and Properties of C-Mn All-Weld-Metal Deposits. Welding Journal, 61(4), 125s-132s.

5.
Gianetto, J.A., Smith, N.J., McGrath, J.T., Bowker, J.T., 1992. Effect of Composition and Energy Input on Structure and Properties of High-Strength Weld Metals. Welding Journal, 71(11), 407s-419s.

6.
Grong, O., 1994. Metallurgical Modelling of Welding. The Institute of Materials, London.

7.
Mukai, A., Nakano, T., Okamoto, H., Morita, K., 2000. Investigation on MAG Welding Wires for Building Structure. Steel Construction Engineering, 7(26), 13-25 (in Japanese).

8.
Schumann, G.O., 1995. The Influence of Welding Variables on Weld Metal Mechanical and Microstructural Properties from Conventional and Microalloyed Rutile Flux-Cored Wires. Trends in Welding Research, June, 525-534.

9.
Tsukamoto, M., Hatano, I., Tsuji, K., Murata, Y., Ichinohe., Y., 2003. Features of the Newly Developed Soild Wire for CO2 Gas Shielded Arc Welding under Large Heat Input and High Interpass Temperature Conditions. Welding Technology, 51(12), 93-98 (in Japanese).

10.
Vercesi, J., Surian, E., 1996. The Effect of Welding Parameters on High Strength SMAW All-Weld-Metal - Part 1: AWS E11018-M. Welding Journal, 75(6), 191s-196s.

11.
Vercesi, J., Surian, E., 1998. The Effect of Welding Parameters on High Strength SMAW All-Weld-Metal - Part 2: AWS E10018-M and E12018-M. Welding Journal, 77(4), 164s-171s.

12.
Yokoyama, Y., 2003. The Welding Methods for the Requirement of High-Quality Weld in the Steel Building Fabrication. Welding Technology, 51(8), 80-88 (in Japanese).