JOURNAL BROWSE
Search
Advanced SearchSearch Tips
Effect of gas detonation on response of circular plate-experimental and theoretical
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Effect of gas detonation on response of circular plate-experimental and theoretical
Babaei, Hashem; Mostofi, Tohid Mirzababaie; Sadraei, Seyed Hamidreza;
 Abstract
A series of experimental results on thin mild steel plates clamped at the boundary subjected to gas detonation shock loading are presented. Detonation occurred by mixing Acetylene (C2H2)-Oxygen (O2) in various volume ratio and different initial pressure. The applied impulse is varied to give deformation in the range from 6 mm to 35 mm. Analytical modeling using energy method was also performed. Dependent material properties, as well as strain rate sensitivity, are included in the theoretical modeling. Prediction values for midpoint deflections are compared with experimental data. The analytical predictions have good agreement with experimental values. Moreover, it has been shown that the obtained model has much less error compared with those previously proposed in the literature.
 Keywords
circular plate;large deformation;gas detonation forming;shock loading;theoretical modeling;
 Language
English
 Cited by
1.
Dynamic compaction of cold die Aluminum powders,;;;;;

Geomechanics and Engineering, 2016. vol.10. 1, pp.109-124 crossref(new window)
1.
Gas mixture detonation method, a novel processing technique for metal powder compaction: Experimental investigation and empirical modeling, Powder Technology, 2017, 315, 171  crossref(new windwow)
2.
Theoretical analysis on the effect of uniform and localized impulsive loading on the dynamic plastic behaviour of fully clamped thin quadrangular plates, Thin-Walled Structures, 2016, 109, 367  crossref(new windwow)
3.
Experimental and Numerical Studies of Sheet Metal Forming with Damage Using Gas Detonation Process, Metals, 2017, 7, 12, 556  crossref(new windwow)
4.
The influence of gas mixture detonation loads on large plastic deformation of thin quadrangular plates: Experimental investigation and empirical modelling, Thin-Walled Structures, 2017, 118, 1  crossref(new windwow)
5.
On dimensionless numbers for the dynamic plastic response of quadrangular mild steel plates subjected to localized and uniform impulsive loading, Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2017, 231, 5, 939  crossref(new windwow)
6.
Experimental and theoretical study on large ductile transverse deformations of rectangular plates subjected to shock load due to gas mixture detonation, Strain, 2017, 53, 4, e12235  crossref(new windwow)
7.
Closed-form analytical analysis on the effect of coupled membrane and bending strains on the dynamic plastic behaviour of fully clamped thin quadrangular plates due to uniform and localized impulsive loading, Thin-Walled Structures, 2018, 123, 48  crossref(new windwow)
8.
Dynamic compaction of cold die Aluminum powders, Geomechanics and Engineering, 2016, 10, 1, 109  crossref(new windwow)
 References
1.
Babaei, H. and Darvizeh, A. (2011), "Investigation into the response of fully clamped circular steel, copper, and aluminum plates subjected to shock loading", Mech. Bas. Des. Struct., 39(4), 507-526. crossref(new window)

2.
Babaei, H. and Darvizeh, A. (2012), "Analytical study of plastic deformation of clamped circular plates subjected to impulsive loading", J. Mech. Mater. Struct., 7(4), 309-322. crossref(new window)

3.
Babaei, H., Mirzababaie Mostofi, T. and Alitavoli, M. (2015a), "Study on the response of circular thin plate under low velocity impact", Geomech. Eng., 9(2), 207-218. crossref(new window)

4.
Babaei, H., Mirzababaie Mostofi, T. and Alitavoli, M. (2015b), "Experimental and theoretical study of large deformation of rectangular plates subjected to water hammer shock loading", Proc. IMechE., PartE: J. Mech. Eng. Sci., DOI: 10.1177/0954408915611055.

5.
Batra, R.C. and Dubey, R.N. (1971), "Impulsively loaded circular plates", Int. J. Solids. Struct., 7(8), 965-978. crossref(new window)

6.
Bisadi, H. and Meybodi, M.K. (2011), "Experimental, numerical, and theoretical analyses of simultaneous forming-welding of inhomogeneous plates", Proc. IMechE., PartC: J. Mech. Eng. Sci., 225(11), 2552-2564. crossref(new window)

7.
Cezary, S. and Bojar, Z. (2008), "Gas detonation spray forming of Fe-Al coatings in the presence of interlayer", Surf. Coat. Tech., 202(15), 3538-3548. crossref(new window)

8.
Duffey, T.A. (1967), "The large deflection dynamic response of clamped circular plates subjected to explosive loading", Sandia Laboratory Research Report No. SC-RR-67-532.

9.
Gharababaei, H. and Darvizeh, A. (2010), "Experimental and analytical investigation of large deformation of thin circular plates subjected to localized and uniform impulsive loading", Mech. Bas. Des. Struct., 38(2), 171-189. crossref(new window)

10.
Ghosh, S.K. and Weber, H. (1976), "Experimental-theoretical corrections of impulsively loaded axisymmetric rigid-plastic membrane", Mech. Res. Commun., 3, 423-428. crossref(new window)

11.
Hadavi, V., Ashani, J.Z. and Mozaffari, A. (2012), "Theoretical calculation of the maximum radial deformation of a cylindrical shell under explosive forming by a new energy approach", Proc. IMechE., PartC: J. Mech. Eng. Sci., 226(3), 576-584. crossref(new window)

12.
Honda, A. and Suzuki, M. (1999), "Sheet metal forming by using gas imploding detonation", J. Mater. Proc. Tech., 85(1), 198-203. crossref(new window)

13.
Hudson, G.E. (1951), "A theory of the dynamic plastic deformation of a thin diaphragm", J. Appl. Phys., 22, 1-11. crossref(new window)

14.
Jones, N. (1989), Structural impact, Cambridge University Press, Cambridge.

15.
Li, F., Mo, J., Zhou, H. and Fang, Y. (2013), "3D Numerical simulation method of electromagnetic forming for low conductive metals with a driver", Int. J. Adv. Manuf. Tech., 64(9-12), 1575-1585. crossref(new window)

16.
Li, L.J. and Jiang, W.K. (2011), "A new effective method to predict the permanent deformation of plane plates subjected to underwater shock loading", Proc. IMechE., PartC: J. Mech. Eng. Sci., 225(5), 1069-1075. crossref(new window)

17.
Lippman, H. (1974), "Kinetics of the axisymmetric rigid-plastic membrane supplied to initial impact", Int. J. Mech. Sci., 16, 297-303. crossref(new window)

18.
Meng, Z., Huang, S., Hu, J., Huang, W. and Xia, Z. (2011), "Effects of process parameters on warm and electromagnetic hybrid forming of magnesium alloy sheets", J. Mater. Proc. Tech., 211(5), 863-867. crossref(new window)

19.
Meybodi, M.K. and Bisadi, H. (2009), "Gas detonation forming by a mixture of $H_2+O_2$ detonation", World Acad. Sci. Eng. Tech., 33, 55-58.

20.
Mynors, D.J. and Zhang, B. (2002), "Applications and capabilities of explosive forming", J. Mater. Proc. Tech., 125, 1-25.

21.
Nurick, G.N. and Martin, J.B. (1989a), "Deformation of thin plates subjected to impulsive loading-a review (partII)", Int. J. Impact. Eng., 8, 171-186. crossref(new window)

22.
Nurick, G.N. and Martin, J.B. (1989b), "Deformation of thin plates subjected to impulsive loading-a review (partI)", Int. J. Impact. Eng., 8, 159-170. crossref(new window)

23.
Perrone, N. and Bhadra, P. (1984), "Simplified large deflection mode solutions for impulsively loaded viscoplastic circular membranes", J. Appl. Mech., 51, 505-509. crossref(new window)

24.
Psyk, V., Risch, D., Kinsey, B.L., Tekkaya, A.E. and Kleiner, M. (2011), "Electromagnetic forming-a review", J. Mater. Proc. Tech., 211(5), 787-829. crossref(new window)

25.
Shen, W.Q. and Jones, N. (1993), "Dynamic response and failure of fully clamped circular plates under impulsive loading", Int. J. Impact. Eng., 13(2), 259-278. crossref(new window)

26.
Shepherd, J.E. (2009), "Structural response of piping to internal gas detonation", J. Press. Vess-T, ASME, 131(3), 031204. crossref(new window)

27.
Skews, B.W., Kosing, O.E. and Hattingh, R.J. (2004), "Use of a liquid shock tube as a device for the study of material deformation under impulsive loading conditions", Proc. IMechE. PartC: J. Mech. Eng. Sci., 218(1), 39-51. crossref(new window)

28.
Symonds, P.S. and Wierzbicki, T. (1979), "Membrane mode solution for impulsively loaded circular plates", J. Appl. Mech., 46, 58-64. crossref(new window)

29.
Wen, H.M. (1998), "Deformation and tearing of clamped circular work-hardening plates under impulsive loading", Int. J. Pres. Ves. Pip., 75, 67-73. crossref(new window)

30.
Wielage, H. and Vollertsen, F. (2011), "Classification of laser shock forming within the field of high speed forming processes", J. Mater. Proc. Tech., 211(5), 953-957. crossref(new window)

31.
Yasar, M. (2004), "Gas detonation forming process and modeling for efficient spring-back prediction", J. Mater. Proc. Tech., 150(3), 270-279. crossref(new window)

32.
Yasar, M., Demirci, H.I. and Kadi, I. (2006), "Detonation forming of aluminium cylindrical cups experimental and theoretical modelling", Mater. Des., 27(5), 397-404. crossref(new window)