Development of new predictive analysis in the orthogonal metal cutting process by utilization of Oxley`s machining theory

- Journal title : Steel and Composite Structures
- Volume 19, Issue 6, 2015, pp.1467-1481
- Publisher : Techno-Press
- DOI : 10.12989/scs.2015.19.6.1467

Title & Authors

Development of new predictive analysis in the orthogonal metal cutting process by utilization of Oxley`s machining theory

Abdelkader, Karas; Mohamed, Bouzit; Mustapha, Belarbi; Redha, Mazouzi;

Abdelkader, Karas; Mohamed, Bouzit; Mustapha, Belarbi; Redha, Mazouzi;

Abstract

This paper presents a contribution to improving an analytical thermo-mechanical modeling of Oxley`s machining theory of orthogonal metals cutting, which objective is the prediction of the cutting forces, the average stresses, temperatures and the geometric quantities in primary and secondary shear zones. These parameters will then be injected into the developed model of Karas et al. (2013) to predict temperature distributions at the tool-chip-workpiece interface. The amendment to Oxley`s modified model is the reduction of the estimation of time-related variables cutting process such as cutting forces, temperatures in primary and secondary shear zones and geometric variables by the introduction the constitutive equation of Johnson-Cook model. The model-modified validation is performed by comparing some experimental results with the predictions for machining of 0.38% carbon steel.

Keywords

orthogonal metals cutting;Oxley`s theory;analytical modeling;Johnson-Cook model;temperature distributions;

Language

English

References

1.

Adibi-Sedeh, A.H., Madhavan, V. and Bahr, B. (2003), "Extension of Oxley's analysis of machining to use different material models", J. Manuf. Sci. Eng., 125(4), 656-666.

2.

Aviral, S. and Martin, B. (2012), "Determination of Johnson-Cook parameters from machining simulations", Computat. Mater. Sci., 52(1), 298-304.

3.

Bates, D. and Watts, D. (1988), Nonlinear Regression Analysis and its Applications, Wiley, New York, NY, USA, pp. 271-272.

4.

Bogdan, P.N. and Milan, D.E. (2014), "Cutting temperature measurement and material machinability", Therm. Sci., 18(1), S259-S268.

5.

Boothroyd, G. (1963), "Temperatures in orthogonal metal cutting", Pro Institution of the Mechanical Engineers, G. I. London, 177(29), 789-810.

6.

Chao, B.T. and Trigger, K.J. (1995), "Temperature distribution at tool-chip interface in metal cutting", Transact. Am. Soc. Mech. Eng. ASME, 75(1), 1107-1121.

7.

Gierlings, S. and Brockmann, M. (2013), "Analytical modeling of temperature distribution using potential theory by reference to broaching Nickel-Based alloys", Adv. Mater. Res., 769, 139-146.

8.

Gierlings, S. and Brockmann, M. (2014), "Analytical model for tool temperature prediction in broaching Nickel-Based alloys", Adv. Mater. Res., 1018, 99-106.

9.

Gilormini, P. (1982), "Contribution a la modelisation de la formation du copeau en usinage des metaux", Ph.D. Dissertation ; Ecole Nationale Superieure des Mines de Paris, French.

10.

Hahn, R.S. (1951), "On the temperature developed at the shear plane in the metal cutting process", Proceedings of First US National Congress of Applied Mechanics, Chicago, Illinois, June, pp. 661-666.

11.

Hastings, W.F., Mathew, P. and Oxley, P.L.B. (1980), "A machining theory for predicting chip geometry, cutting forces etc. from material properties and cutting conditions", Proceeding of the Royal Society of London (GB), A371, pp. 569-587.

12.

Jaspers, S.P.F.C. and Dautzenberg, J.H. (2002), "Material behavior in conditions similar to metal cutting: flow stress in the primary shear zone", J. Mater. Process. Techno., 122(2-3), 322-330.

13.

Johnson, G.R. and Cook, W.H. (1983), "A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures" Proceedings of the 7th International Symposium on Ballistics, The Hague, Netherlands, April, pp.541-547.

14.

Karas, A., Bouzit, M. and Belarbi, M. (2013), "Development of a thermal model in the metal cutting process for prediction of temperature distributions at the tool-chip-workpiece interface", J. Theor. Appl. Mech., 51(3), 552-567.

15.

Karpat, Y. and Ozel, T. (2006), "Predictive analytical and thermal modeling of orthogonal cutting process - Part I: Predictions of tool forces, stresses, and temperature distributions", J. Manuf. Sci. Eng., ASEM, 128(2), 435-444.

16.

Klocke, F., Gierlingsa, S., Brockmann, M. and Veselovac, D. (2014), "Force-based temperature modelling for surface integrity prediction in broaching nickel-based alloys", Proceedings of the 2nd CIRP Conference on Surface Integrity (CSI), Nottingham, England, May.

17.

Komanduri, R. and Hou, Z.B. (2000), "Thermal modeling of the metal cutting process, Part I: temperature rise distribution due to Shear plane heat source", Int. J. Mech. Sci., 42(9), 1715-1752.

18.

Komanduri, R. and Hou, Z.B. (2001a), "Thermal modeling of the metal cutting process, Part II: temperature rise distribution due to frictional heat source at the tool-chip interface", Int. J. Mech. Sci., 43(1), 57-88.

19.

Komanduri, R. and Hou, Z.B. (2001b), "Thermal modeling of the metal cutting process, Part III: temperature rise distribution due to the combined effects of shear plane heat source and the tool-chip interface frictional heat Source", Int. J. Mech. Sci., 43(1), 89-107.

20.

Lalwani, D.I., Mehta, N.K. and Jain, P.K. (2009), "Extension of Oxley's predictive machining theory for Johnson and Cook flow stress model", J. Mater. Process. Technol., 209(12-13), 5305-5312.

21.

Liangshan, X., Jie W., Yiinye, G., Bin, L. and Ning, F. (2014), "Improvement of algorithm and prediction precision of an extended Oxley's theoretical model", Int. J. Adv. Manuf. Technol., 77(1), 1-13. DOI: 10.1007/s00170-014-6361.

22.

Loewen, E.G. and Shaw, M.C. (1954), "On the analysis of cutting tool temperatures", Transact. Am. Soc. Mech. Eng. ASEM, 76(2), 217-231.

23.

Merchant, M.E. (1945), "Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip", J. Appl. Phys., 16(5), 267-279.

24.

Oxley, P.L.B. (1989), The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood Ltd., England.

25.

Oxley, P.L.B. and Hastings, W.F. (1975), "Minimum work as a possible criterion for determining the frictional conditions at the tool/chip interface in machining", Proc. Instn. Mech. Engrs, 282(A1310), 565-584.

26.

Özel, T. and Zeren, E. (2006), "A methodology to determine work material flow stress and tool-chip interfacial friction properties by using analysis of machining", J. Manuf. Sci. Eng., 128(1), 119-129.

27.

Tounsi, N., Vincenti, J., Otho, A. and Elbestawi, M.A. (2002), "From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation", Int. J. Mach. Tools Manuf., 42(12), 1373-1383.

28.

Trigger, K.J. and Chao, B.T. (1951), "An analytical evaluation of metal cutting temperature", Transact. Am. Soc. Mech. Eng. ASME, 73, 57-68.