Advanced SearchSearch Tips
Anode-supported Type SOFCs based on Novel Low Temperature Ceramic Coating Process
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
Anode-supported Type SOFCs based on Novel Low Temperature Ceramic Coating Process
Choi, Jong-Jin; Ahn, Cheol-Woo; Kim, Jong-Woo; Ryu, Jungho; Hahn, Byung-Dong; Yoon, Woon-Ha; Park, Dong-Soo;
  PDF(new window)
To prevent an interfacial reaction between the anode and the electrolyte layer during the conventional high-temperature co-firing process, an anode-supported type cell with a thin-film electrolyte was fabricated by low-temperature ceramic thick film coating process. Ni-GDC cermet composite was used as the anode material and YSZ was used as the electrolyte material. Open circuit voltage and maximum power density were found to strongly depend on the surface uniformity of the anode functional layer. By optimizing the microstructure of the anode functional layer, the open circuit voltage and maximum powder density of the cell increased to 1.11 V and , respectively, at . When a GDC barrier layer was applied between the YSZ electrolyte and the LSCF cathode, the cell showed good stability, with almost no degradation up to 100 h. Anode-supported type SOFCs with high performance and good stability were fabricated using a coating process.
SOFC;Anode-supported type;Coating;Low temperature process;
 Cited by
Improving the efficiency of layered perovskite cathodes by microstructural optimization, J. Mater. Chem. A, 2017, 5, 17, 7896  crossref(new windwow)
N. Q. Minh and T. Takahashi, Science and Technology of Ceramic Fuel Cell, Elsevier Science, 1995.

J. Will, A. Mitterdorfer, C. Kleinlogel, D. Perednis, and L. J. Gauckler, "Fabrication of Thin Electrolytes For Secondgeneration Solid Oxide Fuel Cells," Solid State Ionics, 131 79-96 (2000). crossref(new window)

S. P. Simmer, M. D. Anderson, M. H. Engelhard, and J. W. Stevenson, "Degradation Mechanisms of La-Sr-Co-Fe-$O_3$ SOFC Cathodes," Electrochem. Solid-State Lett, 9 A478-81 (2006). crossref(new window)

K. Huang, J. H. Wan, and J. B. Goodenough, "Increasing Power Density of LSGM-based Solid Oxide Fuel Cells Using New Anode Materials," J. Electrochem. Soc., 148 A788 (2001). crossref(new window)

T. Kawada, N. Sakai, H. Yokokawa, M. Dokiya, and I. Anzai, "Fabrication of a Planar Solid Oxide Fuel Cell by Tape-casting and Co-firing Method," J. Ceram. Soc. Jpn., 100 [1162] 847-50 (1992). crossref(new window)

D. Rotureau, J. -P. Viricelle, C. Pijolat, N. Caillol, and M. Pijolat, "Development of a Planar SOFC Device Using Screen-printing Technology," J. Eur. Ceram. Soc. 25 [12] 2633-36 (2005). crossref(new window)

Y. J. Leng, S. H. Chan, K. A. Khor, S. P. Jiang, and P. Cheang, "Effect of Characteristics of $Y_2O_3/ZrO_2$ Powders on Fabrication of Anode-supported Solid Oxide Fuel Cells," J. Power Sources, 117 [1/2] 26-34 (2003). crossref(new window)

W. Li, K. Hasinska, M. Seabaugh, S. Swartz, and J. Lannutti, "Curvature in Solid Oxide Fuel Cells," J. Power Sources, 138 [1/2] 145-55 (2004). crossref(new window)

M. F. Carolan and J. N. Michaels, "Growth Rates and Mechanism of Electrochemical Vapor Deposited Yttria-stabilized Zirconia Films," Solid State Ionics, 37 [2/3] 189-96 (1990). crossref(new window)

H.Y. Jung, K. S. Hong, H. Kim, J. K. Park, J. W. Son, J. Kim, H. W. Lee, and J. H. Lee, "Characterization of Thinfilm YSZ Deposited via EB-PVD Technique in Anode-supported SOFCs," J. Electrochem. Soc., 153 [6] A961-66 (2006). crossref(new window)

T. Ishihara, K. Sato, and Y. Takita, "Electrophoretic Deposition of $Y_2O_3$-stabilized $ZrO_2$ Electrolyte Films in Solid Oxide Fuel Cells," J. Am. Ceram. Soc., 79 [4] 913-19 (1996). crossref(new window)

T. Setoguchi, M. Sawano, K. Eguchi, and H. Arai, "Application of the Stabilized Zirconia Thin Film Prepared by Spray Pyrolysis Method to SOFC," Solid State Ionics, 40-41 [1] 502-5 (1990). crossref(new window)

M. Gaudon, Ch. L. Robert, F. Ansart, and P. Stevens, "Thick YSZ Films Prepared Via a Modified Sol-gel Route: Thickness Control (8-80 mm)," J. Eur. Ceram. Soc., 26 3153-60 (2006). crossref(new window)

G. Schiller, R. H. Henne, M. Lang, R. Ruckdaeschel, and S. Schaper, "Development of Vacuum Plasma Sprayed Thinfilm SOFC for Reduced Operating Temperature," Fuel Cells Bull., 21 [3] 7-12 (2000).

J.-J. Choi, S.-H. Oh, H.-S. Noh, H.-R. Kim, J.-W. Son, D.-S. Park, J.-H. Choi, J. Ryu, B.-D. Hahn, W.-H. Yoon, H.-W. Lee, "Low Temperature Fabrication of Nano-structured Porous LSM-YSZ Composite Cathode Film by Aerosol Deposition," J. Alloy. Compd., 509 2627-30 (2011). crossref(new window)

J.-J. Choi, K.-S. Cho, J.-H. Choi, J. Ryu, B.-D. Hahn, J.-W. Kim, C.-W. Ahn, W.-H. Yoon, D.-S. Park, and J. Yun, "Electrochemical Effects of Cobalt Doping on $(La,Sr)(Ga,Mg)O_{3-{\delta}}$ Electrolyte Prepared by Aerosol Deposition," Int. J. Hydrogen Energy, 37 6830-35 (2012). crossref(new window)

J.-J. Choi, J.-H. Choi, J. Ryu, B.-D. Hahn, J.-W. Kim, C.-W. Ahn, W.-H. Yoon, and D.-S. Park, "Microstructural Evolution of YSZ Electrolyte Deposited on Porous NiO-YSZ by Aerosol Deposition," J. Eur. Ceram. Soc., 32 3249-54 (2012). crossref(new window)

J.-J. Choi, J. Ryu, B.-D. Hahn, C.-W. Ahn, J.-W. Kim, W.- H. Yoon, and D.-S. Park, "Low Temperature Preparation and Characterization of Solid Oxide Fuel Cells on FeCr- Based Alloy Support by Aerosol Deposition," Int. J. Hydrogen Energy, 39 [24] I2878-83 (2014).

J.-J. Choi, D.-S. Park, B.-D. Hahn, J. Ryu, and W.-H. Yoon, "Oxidation Behavior of Ferritic Steel Alloy Coated with Highly Dense Conducting Ceramics by Aerosol Deposition," J. Am. Ceram. Soc., 91 [8] 2601-6 (2008). crossref(new window)

J.-J. Choi, D.-S. Park, B.-G. Seong, and H.-Y. Bae, "Lowtemperature Preparation of Dense $(Gd,Ce)O_{2-{\delta}}-Gd_2O_3$ Composite Buffer Layer by Aerosol Deposition for YSZ Electrolyte- based SOFC," Int. J. Hydrogen Energy, 37 9809-15 (2012). crossref(new window)