Publisher : The Korean Society for Technology of Plasticity
DOI : 10.5228/KSTP.24.4.293
Title & Authors
Manufacturing Integral Safety Vents in Prismatic Lithium-ion Batteries Kim, J. H.; Lee, K. H.; Lim, Y. J.; Kim, B. M.;
A safety vent is crucial to protect its user from unpredictable explosions caused by increasing internal pressure of the lithium-ion batteries. In order to prevent the explosion of the battery, a safety vent rupture is required when the internal pressure reaches a critical value. In conventional manufacturing, the cap plate and the safety vent are fabricated separately and subsequently welded to each other. In the current study, a manufacturing process including a backward extrusion and coining process is suggested to produce an integral safety vent which also has the benefit of increasing production efficiency. FE simulations were conducted to predict the rupture pressure and to design the safety vent using a ductile fracture criterion and the element deletion method. The critical value, C, in the ductile fracture criterion was obtained from uniaxial tensile tests with an annealed sheet of 1050-H14 aluminum alloy. Rupture tests were preformed to measure the rupture pressure of the safety vent. The results met the required rupture pressure within 8.5±0.5 kgf/cm2. The simulation results were compared with experimental results, which showed that the predicted rupture pressures are in good agreement with experimentally measured ones with a maximum error of only 3.9%.
T. Ohsaki, T. Kishi, T. Kuboki, N. Takami, N. Shimura, Y. Sato, M. Sekino, A. Satoh, 2005, Overcharge Reaction of Lithium-ion Batteries, J. Power Sources, Vol. 46, No. 1-2, pp. 97~100.
M. Majima, T. Tada, S. Ujiie, E. Yagasaki, S. Inazawa, K. Miyazaki, 1999, Design and Characteristics of Large-scale Lithium Ion Battery, J. Power Sources, Vol. 81, pp. 877~881.
K. H. Kwon, S. H. Moon, M. C. Kim, S. M. Oh, M. S. Kim, 2003, Fabrication of Carbon Nanofiber/Graphite Electrodes for Lithium Ion Secondary Battery, J. Korean Oil Chem. Soc., Vol. 20, No. 2, pp. 130~140.
S. M. Kim, W. J. Song, T. W. Ku, J. Kim, B. S. Kang, 2009, Study on Bursting Prediction of Rectangular Battery Case with V-notch, Trans. Mater. Process, Vol. 18, No. 1, pp. 59~66.
J. H. Lee, H. M. Lee, S. H. Ann, 2003, Battery Dimensional Changes Occurring Charge/discharge Cycles-thin Rectangular Lithium Ion and Polymer Cells, J. Power Sources, Vol. 119, pp. 833~837.
J. Barker, 1999, In-situ Measurement of the Thickness Changes Associated with Cycling of Prismatic Lithium Ion Batteries Based on LiMn2O4 and LiCoO2, Elctrochim. Acta, Vol. 45, No. 1-2, pp. 235~242.
Y. Lou, S. B. Kim, H. Huh, 2010, Analytical Study of the Effect of Material Properties on the Formability of Sheet Metals based on the M-K Model, Trans. Mater. Process, Vol. 19, No. 7, pp. 393~398.
H. Takuda, K. Mori, N. Hatta, 1999, The Application of some Criteria for Ductile Fracture to the Prediction of the Forming Limit of Sheet Metals, J. Mater. Process. Technol., Vol. 95, No. 1-3, pp. 116~121.
S. E. Clift, P. Hartely, C. E. N. Sturgess, G. W. Rowe, 1990, Fracture Prediction in Plastic Deformation Processes, J. Mater. Process. Technol., Vol. 32, No. 1, pp. 1~17.