Advanced SearchSearch Tips
Evaluation of Friction Characteristics for High-Strength-Steel Sheets Depending on Conditions
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
  • Journal title : Transactions of Materials Processing
  • Volume 24, Issue 6,  2015, pp.381-386
  • Publisher : The Korean Society for Technology of Plasticity
  • DOI : 10.5228/KSTP.24.6.381
 Title & Authors
Evaluation of Friction Characteristics for High-Strength-Steel Sheets Depending on Conditions
Kim, J. E.; Heo, J. Y.; Yoon, I. C.; Song, J. S.; Youn, K. T.; Park, C. D.;
  PDF(new window)
Recently, high-strength-steel sheets have been used extensively for increasing fuel-efficiency and stability in automobiles. A study on the characteristics regarding friction factors is required because high-strength-steel sheets have higher contact pressure at the tool interface as compared to low-strength steel sheets. For the current study, a sheet friction test was used to examine the influence of several factors on friction. The friction tests were performed on two types of sheet steels (SPFC590 and SPFC980) to obtain friction coefficients as a function of contact pressure, surface roughness, lubricant viscosity, and speed. Based on the experimental results for SPFC590 and SPFC980, the friction coefficient decreased with increasing contact pressure, but the friction coefficient increased with increasing surface roughness. Also, the friction coefficient decreased with increasing lubricant viscosity and decreasing speed.
Friction Coefficient;Tool Surface Roughness;Lubricant Viscosity;High-Strength-Steel Sheet;
 Cited by
Y. Tamai, T. Fujita, T. Inazumi, K. Manabe, 2013, Effects of Contact Pressure, Sliding Velocity and Sliding Length on Friction Behavior of High-Tensile-Strength Steel Sheets, J. Jpn. Soc. Technol. Plast., Vol. 54, No. 629, pp. 537~541. crossref(new window)

S. S. Han, 2011, Contact Pressure Effect on Frictional Behavior of Sheet for Automotive Stamping, Trans. Mater. Process., Vol. 20, No. 2, pp. 99~103. crossref(new window)

B. H. Lee, Y. T. Keum, 2001, Friction Model of Sheet Metal Forming Considering Lubricant and Surface Roughness, Trans. Mater. Process., Vol. 10, No. 7, pp. 543~550.

B. H. Lee, Y. T. Keum, 2002, Friction Model for Sheet Metal Forming Analysis, Trans. Mater. Process., Vol. 11, No. 4, pp. 349~354. crossref(new window)

S. S. Han, K. C. Park, 2008, Effect of Surface Roughness on Frictional Behavior of Sheet Steel for Automotive, Trans. Mater. Process., Vol. 17, No. 6, pp. 401~406. crossref(new window)

N. J. Kim, Y. T. Keum, 2013, Experimental Determination of Friction Characteristics for Advanced High Strength Steel Sheets, Trans. Mater. Process., Vol. 22, No. 4, pp. 223~228. crossref(new window)

J. M. Lanzon, M. J. Cardew-Hall, P. D. Hodgson, 1998, Characterising Frictional Behavior in Sheet Metal Forming, J. Mater. Process. Technol. Vol. 80-81, pp. 251~256. crossref(new window)

H. Kim, S. Han, Q. Yanc, T. Altan, 2008, Evaluation of Tool Materials, Coatings and Lubricants in Forming Galvanized Advanced High Strength Steels (AHSS), CIRP Ann.-Manuf. Technol., Vol. 57, pp. 299~304. crossref(new window)

S. H. Chang, K. H. Shin, Y. J. Jeon, Y. M. Heo, 2012, Proc. Kor. Soc. Tech. Plast. Spring Conf., Kor. Soc. Tech. Plast., Seoul, Korea, pp. 538-541.

J. H. Yoo, J. R. Seo, S. K. Lee, 1999, Proc. Kor. Soc. Precis. Eng. Autumn Conf., Kor. Soc. Precis. Eng., Seoul, Korea, pp. 320-323.

C. G. Kim, 2006, Tribology, Hyungseul Publishing, Seoul, Korea, pp. 3~605.