JOURNAL BROWSE
Search
Advanced SearchSearch Tips
A Study on the Improvement of Efficiency of Heat Transfer of Double Pipe Heat Exchanger with Helical Insert Device on Cooling of a Fuel Cell
facebook(new window)  Pirnt(new window) E-mail(new window) Excel Download
 Title & Authors
A Study on the Improvement of Efficiency of Heat Transfer of Double Pipe Heat Exchanger with Helical Insert Device on Cooling of a Fuel Cell
CHO, Dong-Hyun;
  PDF(new window)
 Abstract
The present study was conducted on the improvement of the heat transfer performance of double pipe heat exchangers with helical insert device. Double pipe heat exchangers with helical insert device were studied for improvement of the heat transfer performance of double pipe heat exchangers with helical insert device and plain double pipe heat exchangers were also studied to comparatively analyze heat transfer performance. Experimental results were derived on changes in the Reynold's numbers of the cooling water flowing in helical and plain double pipe heat exchangers and changes in the heat flux of the air. Thereafter, to verify the reliability of the experimental results, the theoretical total energy and the experimental total energy were comparatively analyzed and the following results were derived. The thermal energy of the calorie lost by the hot air and that of the calorie obtained by the cooling water were well balanced. The experiments of plain double pipe heat exchangers and double pipe heat exchangers with helical insert device were conducted under normal conditions and the theoretical overall heat transfer coefficient value and the experimental overall heat transfer coefficient value coincided well with each other. In both plain double pipe heat exchangers and double pipe heat exchangers with helical insert device, heat transfer rates increased as the cooling water flow velocity increased. Under the same experimental conditions, the heat transfer performance of double pipe heat exchangers with helical insert device was shown to be higher by approximately 1.5 times than that of plain double pipe heat exchangers.
 Keywords
Double pipe heat exchanger with helical insert device;Heat transfer performance;Improvement of efficiency;Cooling of a fuel cell;
 Language
Korean
 Cited by
1.
연료전지 냉각용 헬리컬 인서트디바이스 이중관열교환기의 열전달 성능 향상에 관한 연구,조동현;

수산해양교육연구, 2015. vol.27. 6, pp.1872-1879 crossref(new window)
 References
1.
Bergles, A. E. and Lopina, R. F.(1969). Heat Transfer and Pressure Drop in Tape Generated Swirl Flow of Single-Phase Water." J. Heat Transfer, Trans. ASME. Vol. 9, 434-442.

2.
Cho, D. H.(2015). A Study on the Improvement of Efficiency of Heat Transfer of Double Pipe Heat Exchanger with Helical Insert Device on Cooling of a Fuel Cell, Jour. Fish. Mar. Sci. Edu., 27(6).

3.
Chyu, M. K..Yu, Y..Ding, H..Downs, J. P.. Soechting, F. O.(1997). "Concavity enhanced heat transfer in an internal cooling passage," IGTI, 97-DT-437, Oriando, Florida, USA.

4.
Fan, L. T..Lin L. S. and Azer, N. Z.(1978). "Surface Renewal Model of Condensation Heat Transfer in Tubes with in-line static Mixers." Int. J. Heat mass Transfer vol.21, 849-854. crossref(new window)

5.
Garimella, S. and Christensen, R. N.(1995). Heat Transfer and Pressure Drop Characteristics of Spirally Fluted Annuli: Part I- Hydropdynamics, Journal of Heat Transfer, Vol. 117, 54-60. crossref(new window)

6.
Incropera, F. P..Dewitt, D. P..Bergman, T. L. and Lavine, A. S.(2014). Fundamental of Heat Transfer, Incropera, 420-450.

7.
Lim, T. W..You, S. S.(2008). A Study on the microcooling Fin Fabrication Process for Enhancing Boiling Heat Transfer, Jour. Fish. Mar. Sci. Edu., 19(3), 366-372.

8.
Lim, T. W..Park, J. U. & Kim. J. H.(2002). A Study on Heat Transfer and Pressure Drop in Flow Boiling of Binary Mixtures in a Uniformly Heated Horizontal Tube, Jour. Fish. Mar. Sci. Edu., 14(2), 177-190.

9.
MIFFAF(2012). Annual Statistics of Agriculture, Forestry, Fishery and Food.

10.
Park, J. U..Cho, D. H.(2004). A Study on Heat Transfer Characteristics of Helical Coiled Tube, Jour. Fish. Mar. Sci. Edu., 16(2), 257-270.

11.
Smithberg, E. and Landis, F.(1964). "Friction and Forced Convection Heat-Transfer Characteristics in Tubes With Twisted Tape Swirl Generators." J. Heat Transfer.Trans. ASME, vol.86, 39-49. crossref(new window)

12.
Thorsen, R. and Landis, F.(1968). "Friction and Heat Transfer Characteristics in Turbulent Swirl Flow Subjected to Large Transverse Temperature Gradients." J. Heat Transfer Trans. ASME, vol.90, 87-97. crossref(new window)