DOI QR코드

DOI QR Code

Excitation and Measurement Points Selection to Identify Structural Parameters for Model Tuning

모델보정을 위한 구조물 매개변수 규명시 가진점 .측정점의 선정

  • Published : 2000.05.01

Abstract

A sensor placement technique to identify structural parameter was developed. Experimental results must be acquired to identify unknown dynamic characteristics of a targeting structure for the comparison between analytical model and real structure. If the experimental environment was not equipped itself properly, it can be happened that some valuable information are distorted or ill-condition can be occurred. In this work the index to determine exciting points was derived from the criterion of maximizing parameter sensitivity matrix and that to choose measurement points was from that of preserving the invariant of sensitivity matrix. This idea was applied to a compressor hull structure to verify its performance. The result shows that the selection of measurement and excitation points using suggested criteria improve the ill-conditioning problem of inverse type problems such , as model updating

Keywords

Sensor Placement;Parameter Identification;Model Tuning

References

  1. S. Bayard, 1988, 'Optimal Experiment Design for Identification of Large Space Structures,' Automatica, Vol. 24, No. 3, pp. 357-364 https://doi.org/10.1016/0005-1098(88)90076-3
  2. Kim, H. B. and Park, Y. S., 1997, 'Sensor Placement Guide for Structural Joint Stiffness Model Improvement,' Mechanical Systems and Signal Processing, Vol. 11 No. 5, pp. 651-672 https://doi.org/10.1006/mssp.1997.0108
  3. Berman, A. and Flannelly, W. G., 1971, 'Theory of Incomplete Models of Dynamic Structures,' AIAA, Vol. 9, No. 8, pp. 1481-1487
  4. Friswell, M. I. and Mottershead, J. E., 1996, Finite Element Model Updating in Structural Dynamics, Kluwer Academic Publisher
  5. Wang, H. and Liou, C.M., 1990, 'Identification of Parameters of Structural Joints by Use of Noise Contaminated FRFs,' Journal of Sound and Vibration, Vol. 142, No. 2, pp. 261-277 https://doi.org/10.1016/0022-460X(90)90556-F
  6. Wang, H., 1989, 'Experimental Structure Synthesis with Special Consideration of Joint Effects,' The International Journal of Analytical and Experimental Modal Analysis, Vol. 5, No. 1, pp. 13-24
  7. Kim, H. B., Lee, S. S. and Park, Y. S., 1998, 'Structural Joint Characteristic Identification Using Optimal Experimental Design Technique,' 16th IMAC, pp. 1388-1394
  8. Kubrusly, S., 1985, 'Sensors and Controllers Location in Distributed Systems; A Survey,' Automatica, Vol. 21, No. 2, pp. 117-182 https://doi.org/10.1016/0005-1098(85)90107-4
  9. Qureshi, H., 1980, 'Optimal Experiment Design for Identification of Distributed Parameter Systems,' Int. J. Control, Vol. 31, No. 1, pp. 21-29 https://doi.org/10.1080/00207178008961025
  10. Baruch, M., 1978, 'Optimization Procedure to Correct Stiffness and Flexibility Matrix Using Vibration Tests,' AIAA, Vol.16 pp. 1208-1210
  11. Berman, A., 1979, 'Mass Matrix Correction Using An Incomplete Set of Measured Modes,' AIAA, Vol.17, pp. 1147-1148
  12. Kabe, A. M., 1985, 'Stiffness Matrix Adjustment Using Mode Data,' AIAA, Vol. 23, pp. 1431-1436
  13. Baruch, M., 1998, 'Damage Detection Based on Reduced Measurements,' Mechanical Systems and Signal Processing, Vol. 12, No. 1, pp. 23-46 https://doi.org/10.1006/mssp.1996.0132
  14. Ahmadian H., Mottershead, J. E. and Friswell, M. I., 1998, 'Regularization Methods for Finite Element Model Updating,' Mechanical Systems and Signal Processing, Vol. 12, No. 1, pp. 47-64 https://doi.org/10.1006/mssp.1996.0133
  15. Liu, C. and Tasker, F. A., 1996, 'Sensor Placement for Time-Domain Modal Parameter Estimation,' J. Guidance, Control, and Dynamics, Vol. 19, No. 6, pp. 1349-1356
  16. Tongco, E. and Meldrum, D., 1996, 'Optimal Sensor Placement of Large Flexible Space Structure,' J. Guidance, Control, and Dynamics, Vol. 19, No. 4, pp. 961-963
  17. Link, M., 1998, 'Updating Analytical Models By Using Local And Global Parameters And Relaxed Optimization Requirement,' Mechanical Systems and Signal Processing, Vol. 12, No. 1, pp. 7-22 https://doi.org/10.1006/mssp.1997.0131