DOI QR코드

DOI QR Code

Adhesion and Friction Forces of Micro Surface Bumps

마이크로 표면돌기의 응착력과 마찰력

  • 조성산 (홍익대학교 기계 시스템디자인공학과) ;
  • 임제성 (홍익대학교 대학원) ;
  • 박승호 (홍익대학교 기계 시스템디자인공학과) ;
  • 이승섭 (한국과학기술원 기계공학과)
  • Published : 2004.08.01

Abstract

Adhesion and friction forces influence adversely on performance and durability of MEMS. It has been reported that the adhesion and friction forces can be reduced with the introduction of micro surface bumps into the contacting interfaces. In this study experiments were conducted to investigate comparatively the effect of hemispherical and torus micro bumps on the adhesion and friction forces. It is confirmed that micro bumps reduce the adhesion and friction forces, and their effect is more pronounced with the bumps of smaller outer boundary radius. Moreover, the results shows that the torus bumps exhibit more rapid decrease of the adhesion and friction forces with the decrease in the outer boundary radius of bump than the hemispherical bumps. When the magnitude of adhesion force is same, the torus bumps generate smaller friction force than the hemispherical bumps. The usage of hemispherical and torus bumps to reduce the adhesion and friction forces in MEMS is discussed.

Keywords

Hemispherical Bump;Torus Bump;Adhesion;Friction;MEMS

References

  1. Tas, N., Sonnenberg, T., Jansen, H., Legtenberg, R., and Elwenspoek, M., 1996, 'Stiction in Surface Micromachining,' J. Micromech. Microeng., Vol. 6, pp. 385-397 https://doi.org/10.1088/0960-1317/6/4/005
  2. Komvopoulos, K., 1996, 'Surface Engineering and Microtribology for Microelectromechanical systems,' Wear, Vol. 200, pp. 305-327 https://doi.org/10.1016/S0043-1648(96)07328-0
  3. Maboudian, R., 1998, 'Surface Processes in MEMS Technology,' Surface Science Reports, Vol. 30, pp. 207-269 https://doi.org/10.1016/S0167-5729(97)00014-9
  4. Fan, L.-S., Tai, Y.-C., and Muller, R. S., 1989, 'IC-processed electrostatic micromotors,' Sensors and Actuators, Vol. 20, pp. 41-47 https://doi.org/10.1016/0250-6874(89)87100-8
  5. Yufeng, L. and Menon, A. K., 1995, 'The Developement and Implementation of Discrete Texture for the Improvement of Tribological Performance,' Trans. ASME. J. Tribology, Vol. 117, pp. 279-284 https://doi.org/10.1115/1.2831243
  6. Ando, Y., and Ino, J., 1996, 'Friction and Pull-off Force on Silicon Surface Modified by FIB,' Sensors and Actuators A, Vol. 57, pp.83-89 https://doi.org/10.1016/S0924-4247(97)80098-2
  7. Ando, Y., and Ino, J., 1998, 'Friction and Pull-off Forces on Submicron-size Asperities,' Wear, Vol. 216, pp. 115-122 https://doi.org/10.1016/S0043-1648(97)00158-0
  8. Ando, Y., 2000, 'The Effect of Relative Humidity on Friction and Pull-off Forces Measured on Submicron-size Asperity Arrays,' Wear, Vol. 238, pp. 12-19 https://doi.org/10.1016/S0043-1648(99)00334-8
  9. Lee, S. K., Lee, K. C., and Lee, S. S., 2002, 'Micro lens Fabrication Method by the Modified LIGA Process,' Trans. of KSME A, Vol. 26, No. 11, pp. 2450-2456
  10. Cho, S.-S., and Yang, S. M., 2002, 'Finite Element Analysis of Adhesive Contact of Torus-Shaped Bumps,' Journal of the KSTLE, Vol. 18, No.4, pp. 249-254
  11. Cho, S.-S., and Park, S., 2002, 'Finite Element Modeling of a Hemispherical Asperity Adhesively Contacting the Plane Surface of Semi-Infinite Rigid Body,' Trans. of KSME(A), Vol. 26, No. 11, pp. 2436-2441 https://doi.org/10.3795/KSME-A.2002.26.11.2436