Transactions of the Korean Society of Mechanical Engineers A (대한기계학회논문집A)
- Volume 33 Issue 6
- /
- Pages.560-567
- /
- 2009
- /
- 1226-4873(pISSN)
- /
- 2288-5226(eISSN)
Abstract
This paper was designed to estimate the adhesion strength of galvannealed coatings on steel sheets. The adhesion strength were evaluated using single lap - shear tests where the lap joint was bonded by structural adhesive. Tests were performed for overlap length of 5mm, 10mm and 15 mm and three directions (0, 45, 90) of steel sheets used as the adherend of the overlap joint. After the tests, FE simulations of the single lap-shear test were also carried out to observe the stress distribution in the interface between the adhesive and the coated sheet. The results showed that the joint failure loads obtained from the tensile tests of bonded single lap-joints were the same, regardless of overlap lengths and directions of steel sheets. Also, the failure of galvannealed coatings greatly depended on shear stress distribution in the interface and the value was about 30MPa.
File
References
- Pak, S. W., 1991, 'Study on the Deformation Behaviour of Electrogalvanized Coatings,' PhD Thesis, Northwestern University, USA, Evanston
- Kim, Y. S., Park, K. C. and Cho, J. O., 1991, 'Frictional Characteristics of Electro Zn-Ni Alloy Coated Steel Sheets,' J. of KSME A, Vol. 15, No. 6, pp. 1807-1818
- Kim, B. M., et al., 2006, 'Identification of the Bulk Behavior of Coatings by Nanoindentation Test and FESimulation and Its Application to Forming Analysis of the Coated Steel Sheet,' J. of KSME A, Vol. 30, No. 11, pp. 1425-1432 https://doi.org/10.3795/KSME-A.2006.30.11.1425
- Marder, A. R., 2000, 'The Metallurgy of Zinc-Coated Steel,' Progress in materials science, Vol. 45, pp. 191-271 https://doi.org/10.1016/S0079-6425(98)00006-1
- HiRa, T., et al., 1993, 'Friction Behavior of Coated Steels in Sheet Forming,' J. of JSTP, Vol. 34, No. 393, pp. 1141-1146
- Hayashi, H., 1993, 'Tribology in Sheet Metal Forming,' J. of JSTP, Vol. 34, No. 393, pp. 1114-1121
- Hayashi, H., 1985, 'Behavior of Coating Layer in Forming of Galvanized Steel Sheet,' J. of JSTP, Vol. 26, No. 291, pp. 355-360
- Urai, M., et al., 1997, 'Effect of Press-Forming Conditions and Coating Structure on Flaking Phenomenon in Galvannealed Steel Sheets,' Materials Technology for Automobiles, Vol. 47, No. 2, pp. 29-32
- Rangarajan, V., et al., 1996, 'Influence of Strain State on Powdering of Galvannealed Sheet Steel,' Proceeding of SAE, pp. 63-70
- Adams, R. D., Wake W.C., 1997, 'Structural Adhesive Joint in Engineering,' Chapman & Hall, London
- Petrie E. M., 2007, 'Handbook of Adhesives and Sealants,' Mcgraw-Hill, New York
- Yen, H. Y. and Tandjung D., 2005, 'Mixed Mode Fracture Analysis of the Lap Shear Specimen Test per ASTM D1002,' J. Reinforced Plastics and Composites, Vol. 24, pp. 839-853 https://doi.org/10.1177/0731684405047771
- Hu, G., 1995, 'Mixed Mode Fracture Analysis of Adhesive Lap Joints,' Composite engineering, Vol. 5, pp. 1043-1050 https://doi.org/10.1016/0961-9526(95)00026-J
- Lee, C. J. et al., 2008, 'The Evaluation of Surface and Adhesive Bonding Properties for Cold Rolled Steel Sheet for Automotive Treated by Ar/O2 Atmospheric Pressure Plasma,' J. of the KSME A, Vol. 32, No. 4, pp. 354-361 https://doi.org/10.3795/KSME-A.2008.32.4.354
- ASTM D1876-01
Cited by
- Vibro-acoustic characteristics of an annular disk with narrow radial slots vol.11, pp.5, 2010, https://doi.org/10.1007/s12541-010-0081-5
- Sound radiation from in-plane vibration of thick annular discs with a narrow radial slot vol.227, pp.5, 2013, https://doi.org/10.1177/0954406212451066
- Strength Evaluation of Pb-free Solder Joints with Artificial Aging Time and Test Temperature vol.22, pp.3, 2014, https://doi.org/10.7467/KSAE.2014.22.3.090