DOI QR코드

DOI QR Code

Automatic Combination & Assembly System for Phone Camera Lens Module

폰 카메라 렌즈모듈 자동 조합시스템 개발

  • Song, Jun Yeob (Dept. of Ultra Precision Machines & Systems, KIMM) ;
  • Ha, Tae Ho (Dept. of Ultra Precision Machines & Systems, KIMM) ;
  • Lee, Chang Woo (Dept. of Ultra Precision Machines & Systems, KIMM) ;
  • Kim, Dong Hoon (Dept. of Ultra Precision Machines & Systems, KIMM) ;
  • Jeon, Jong (Optical Device Division, N2A Co., Ltd.)
  • 송준엽 (한국기계연구원 초정밀시스템연구실) ;
  • 하태호 (한국기계연구원 초정밀시스템연구실) ;
  • 이창우 (한국기계연구원 초정밀시스템연구실) ;
  • 김동훈 (한국기계연구원 초정밀시스템연구실) ;
  • 전종 ((주) 엔투에이 광디바이스 사업부)
  • Received : 2013.09.03
  • Accepted : 2013.12.21
  • Published : 2014.02.01

Abstract

An automatic combination and assembly system for phone-camera lens modules was developed. The system enables the assembly of the relative orientation of the individual lenses making up the lens module. Conventional assembly systems assemble a lens module from eight assembly units. The developed system reduces this number to half by combining each lens and a spacer into a single assembly unit. Also, the number of transfer stages for sequential assembly is minimized without increasing the assembly time. Therefore, high productivity and a footprint that is only about 25 % of that of a conventional assembly system can be realized. The system features a modular design to allow it to cope with rapid changes in the market. Only a few components, such as the picker and guide, need to be replaced for changing to a new assembly model.

Keywords

Phone Camera;Lens Module;Assembly;Automation

Acknowledgement

Grant : 신속대응 가능한 BIS 기반 자율지능형 사출성형 시스템 개발

Supported by : 산업통상자원부

References

  1. Lee, Y. B., Kwon, T. H. and Yoon, K., 2002, "Numerical Prediction of Residual Stresses and Birefringence in Injection/Compression Molded Center-Gated Disk, Part 1. Basic Modeling and Results for Injection," Polymer Engineering and Science, Vol. 42, pp. 2246-2272. https://doi.org/10.1002/pen.11114
  2. Lee, Y. B., Kwon, T. H. and Yoon, K., 2002, "Numerical Prediction of Residual Stresses and Birefringence in Injection/Compression Molded Center-Gated Disk, Part 2. Effects of Processing Conditions," Polymer Engineering and Science, Vol. 42, pp. 2273-2292. https://doi.org/10.1002/pen.11115
  3. Michaeli, W., Hebner, S., Klaiber, F. and Forster, J., 2007, "Evaluation of Comparison of Geometrical Accuracy and Optical Performance of Injection Molded and Injection-Compression Molded Plastic Parts," Annals of CIRP, Vol. 56, pp. 545-548. https://doi.org/10.1016/j.cirp.2007.05.130
  4. Suh, S. H., Choi, Y., Roh, H. W. and Doh, H., 2013, "Development of Plastic Lenses for High-Resolution Phone Camera by Injection-Compression Molding," Trans. Korean Soc. Mech. Eng. A, Vol. 37, No. 1, pp. 39-46. https://doi.org/10.3795/KSME-A.2013.37.1.039