SiCf/SiC 복합체의 화학기상침착 거동에 미치는 권선 구조와 침착 변수의 영향

Influence of Winding Patterns and Infiltration Parameters on Chemical Vapor Infiltration Behaviors of SiCf/SiC Composites

  • 김대종 (한국원자력연구원 원자력소재개발부) ;
  • 고명진 (한국원자력연구원 원자력소재개발부) ;
  • 이현근 (한국원자력연구원 원자력소재개발부) ;
  • 박지연 (한국원자력연구원 원자력소재개발부) ;
  • 김원주 (한국원자력연구원 원자력소재개발부)
  • Kim, Daejong (Nuclear Materials Development Division, Korea Atomic Energy Research Institute) ;
  • Ko, Myoungjin (Nuclear Materials Development Division, Korea Atomic Energy Research Institute) ;
  • Lee, Hyeon-Geun (Nuclear Materials Development Division, Korea Atomic Energy Research Institute) ;
  • Park, Ji Yeon (Nuclear Materials Development Division, Korea Atomic Energy Research Institute) ;
  • Kim, Weon-Ju (Nuclear Materials Development Division, Korea Atomic Energy Research Institute)
  • 투고 : 2014.07.29
  • 심사 : 2014.09.18
  • 발행 : 2014.09.30


SiC and its composites have been considered for use as nuclear fuel cladding materials of pressurized light water reactors. In this study, a $SiC_f$/SiC composite as a constituent layer of SiC triplex fuel cladding was fabricated using a chemical vapor infiltration (CVI) process in which tubular SiC fiber preforms were prepared using a filament winding method. To enhance the matrix density of the composite layer, winding patterns, deposition temperature, and gas input ratio were controlled. Fiber arrangement and porosity were the main parameters influencing densification behaviors. Final density of the composites decreased as the SiC fiber volume fraction increased. The CVI process was optimized to densify the tubular preforms with high fiber volume fraction at a high $H_2$/MTS ratio of 20 at $1000^{\circ}C$; in this process, surface canning of the composites was effectively retarded.


  1. J. R. Lamarsh and A. J. Baratta, Introduction to Nuclear Engineering; pp. 623-30, Prentice Hall, New Jersey, 2009.
  2. Y. Katoh, T. Nozawa, and L. L. Snead, "Mechanical Properties of Thin Pyrolitic Carbon Interphase SiC-Matrix Composites Reinforced with Near-stoichiometric SiC Fibers," J. Am. Ceram. Soc., 88 [11], 3088-95 (2005).
  3. H. Feinroth, M. Ales, E. Barringer, G. Kohse, D. Carpenter, and R. Jaramillo, Mechanical Strength of CTP Triplex SiC Fuel Clad Tubes after Irradiation in MIT Research Reactor under PWR Coolant Conditions; pp. 47-58, in Silicon Carbide and Carbon Composites, Vol. 30, Ceramic Engineering and Science Proceeding, Ed. by Y. Katoh and A. Cozzi, John Wiley & Sons, New Jersey, 2009.
  4. A. Kohyama, M. Kotani, Y. Katoh, T. Nakayasu, M. Sato, T. Yamamura, and K. Okamura, "High-performance SiC/SiC Composite by Improved PIP Processing with New Precursor Polymers," J. Nucl. Mater., 238-287, 565-69 (2000).
  5. Y.-H. Ji, I.-S. Han, S. Kim, D.-W. Seo, K-S. Hong, and S.-K. Woo, "Effects of Carbon Fiber Arrangement on Properties of LSI $C_f$-Si-SiC Composites(in Korean)," J. Kor. Ceram. Soc., 45 [9], 561-66 (2008).
  6. J. Y. Park, S. M. Kang, L. H. Park, W.-J. Kim, and W. S. Ryu, "Effect of SiC Whisker Growing on Matrix Filling of the SiC$_f$/SiC Composite," Ceram. Eng. Sci. Proc., 24 [4], 613-20 (2003).
  7. H.-W. Yu, K. Raju, J. Y. Park, and D.-H. Yoon, "Effects of $Al_2O_3-Re_2O_3$ Additive for the Sincerting of SiC and the Fabrication of SiC$_f$/SiC Composite(in Korean)," J. Kor. Ceram. Soc., 50 [6], 364-71 (2013).
  8. J. Y. Park, M. H. Jeong, and W.-J. Kim, "Characterization of Slurry Infiltrated SiC$_f$/SiC Prepared by Electrophoretic Deposition," J. Nucl. Mater., 442, S390-93 (2013).
  9. T. Koyanagi, K. Ozawa, T. Hinoki, K. Shimoda, and Y. Katoh, "Effects of Neutron Irradiation on Mechanical Properties of Silicon Carbide Composites Fabricated by Nano-Infiltrated and Transient Eutectic Phase Process," J. Nucl. Mater., 448 [1-3], 478-86 (2014).
  10. Y. Katoh, T. Nozawa, L. L. Snead, K. Ozawa, and H. Tanigawa, "Stability of SiC and Its Composites at High Neutron Fluence," J. Nucl. Mater., 417 [1-3], 400-05 (2011).
  11. M. G. Jenkins and M. D. Mello, "Fabrication, Processing, and Characterization of Braided, Continuous SiC Fiber-Reinforced/CVI SiC Matrix Ceramic Composites," Mater. Manuf. Process., 11 [1], 99-118 (1996).
  12. D. Kim, J. Lee, J. Y. Park, and W.-J. Kim, "Effect of Filament Winding Methods on Surface Roughness and Fiber Volume Fraction of SiC$_f$/SiC Composite Tubes(in Korean)," J. Kor. Ceram. Soc., 50 [6], 359-63 (2013).
  13. D. Cohen, S.C. Mantell, and L. Zhao, "The Effect of Fiber Volume Fraction on Filament Wound Composite Pressure Vessel Strength," Compos. PART B-Eng., 32, 413-29 (2001).
  14. E. V. Morozov, "The Effect of Filament-winding Mosaic Patterns on the Strength of Thin-walled Composite Shells," Compos. Struct., 76, 123-29 (2006).
  15. S.-D. Liang, F.-Q. Zhang, L.-H. Xia, Q. Yu, and X.-Y. Zhang, "Effect of Preform Structure on Densification Process of Plate C/C Composite," Mater. Sci. Eng. Powder Metall., 17 [2], 252-7 (2012).
  16. X. Hou, H. Li, Y. Chen, and K. Li, "Modeling of Chemical Vapor Infiltration Process for Fabrication of Carbon-Carbon Composites by Finite Difference Methods," Carbon, 37, 669-77 (1999).
  17. B. Reznik, D. Gerthsen, W. Zhang, and K.J. Huttinger, "Microstructure of SiC Deposited from Methyltrichlorosilane," J. Eur. Ceram. Soc., 23, 1499-508 (2003).
  18. D. Kim, W.-J. Kim, J.-E. Jang, S. G. Yoon, D.-J. Kim, and J. Y. Park, "Oxidation of CVD ${\beta}$-SiC in Impurity-controlled Helium Environment at 950$^{\circ}C$(in Korean)," J. Kor. Ceram. Soc., 48 [5], 426-32 (2011).
  19. J. Chin, P. K. Gantzel, and R. G. Hudson, "The Structure of Chemical Vapor Deposited Silicon Carbide," Thin Solid Films, 40, 57-72 (1977).