Cable with discrete negative stiffness device and viscous damper: passive realization and general characteristics

  • Chen, Lin (State Key Laboratory for Disaster Reduction of Civil Engineering, Tongji University) ;
  • Sun, Limin (State Key Laboratory for Disaster Reduction of Civil Engineering, Tongji University) ;
  • Nagarajaiah, Satish (Department of Civil and Environmental Engineering, and Dept. of Mechanical Engineering, Rice University)
  • 투고 : 2014.11.27
  • 심사 : 2015.02.15
  • 발행 : 2015.03.25


Negative stiffness, previously emulated by active or semi-active control for cable vibration mitigation, is realized passively using a self-contained highly compressed spring, the negative stiffness device (NSD).The NSD installed in parallel with a viscous damper (VD) in the vicinity of cable anchorage, enables increment of damper deformation during cable vibrations and hence increases the attainable cable damping. Considering the small cable displacement at the damper location, even with the weakening device, the force provided by the NSD-VD assembly is approximately linear. Complex frequency analysis has thus been conducted to evaluate the damping effect of the assembly on the cable; the displacement-dependent negative stiffness is further accounted by numerical analysis, validating the accuracy of the linear approximation for practical ranges of cable and NSD configurations. The NSD is confirmed to be a practical and cost-effective solution to improve the modal damping of a cable provided by an external damper, especially for super-long cables where the damper location is particularly limited. Moreover, mathematically, a linear negative stiffness and viscous damping assembly has proven capability to represent active or semi-active control for simplified cable vibration analysis as reported in the literature, while in these studies only the assembly located near cable anchorage has been addressed. It is of considerable interest to understand the general characteristics of a cable with the assembly relieving the location restriction, since it is quite practical to have an active controller installed at arbitrary location along the cable span such as by hanging an active tuned mass damper. In this paper the cable frequency variations and damping evolutions with respect to the arbitrary assembly location are then evaluated and compared to those of a taut cable with a viscous damper at arbitrary location, and novel frequency shifts are observed. The characterized complex frequencies presented in this paper can be used for preliminary damping effect evaluation of an adaptive passive or semi-active or active device for cable vibration control.


  1. Caracoglia, L. and Jones, N.P. (2007a), "Damping of taut-cable systems: Two dampers on a single stay", J. Eng. Mech. - ASCE, 133(10), 1050-1060.
  2. Caracoglia, L. and Jones, N.P. (2007b), "Passive hybrid technique for the vibration mitigation of systems of interconnected stays", J. Sound Vib., 307(3-5), 849-864.
  3. Chen, L. and Sun, L. (2014), "Laboratory-scale experimental setup for studying cable dampers", J. Eng. Mech. - ASCE, 10.1061/(ASCE)EM.1943-7889.0000878, 04014159.
  4. Chen, Z.Q., Wang, X.Y., Ko, J.M., Ni, Y.Q., Spencer Jr., B.F. and Yang, G. (2003), "MR damping system on Dongting Lake cable-stayed bridge", Proceedings of the SPIE - The Int. Society for Optical Engineering, 229-235.
  5. Fujino, Y. and Hoang, N. (2008), "Design formulas for damping of a stay cable with a damper", J. Struct. Eng. - ASCE, 134(2), 269-278.
  6. Fujino, Y., Kimura, K. and Tanaka, H., (2012), Wind Resistant Design of Bridges in Japan, Springer, Japan.
  7. Hikami, Y. and Shiraishi, N. (1988), "Rain-wind induced vibrations of cables stayed bridges", J. Wind Eng. Ind. Aerod., 29(13), 409-418.
  8. Hoang, N. and Fujino, Y. (2007), "Analytical study on bending effects in a stay cable with a damper", J. Eng. Mech. - ASCE, 133(11), 1241-1246.
  9. Hoang, N. and Fujino, Y. (2008), "Combined damping effect of two dampers on a stay cable", J. Bridge Eng., 13(3), 299-303.
  10. Hoang, N. and Fujino, Y. (2009), "Multi-mode control performance of nonlinear dampers in stay cable vibrations", Struct. Control Health Monit., 16(7-8), 860-868.
  11. Hogsberg, J.R. and Krenk, S. (2006), "Linear control strategies for damping of flexible structures", J. Sound Vib., 293(1-2), 59-77.
  12. Hogsberg, J. (2011), "The role of negative stiffness in semi-active control of magneto-rheological dampers", Struct. Control Health Monit., 18(3), 289-304.
  13. Huang, H., Sun, L. and Jiang, X. (2012), "Vibration mitigation of stay cable using optimally tuned MR damper", Smart Struct. Syst., 9(1), 35-53.
  14. Huang, Z. and Jones, N.P. (2011), "Damping of taut-cable systems: Effects of linear elastic spring support", J. Eng. Mech. - ASCE, 137(7), 512-518.
  15. Iemura, H. and Pradono, M.H. (2003), "Application of pseudo-negative stiffness control to the benchmark cable-stayed bridge", J. Struct. Control, 10(3-4), 187-203.
  16. Iemura, H., Igarashi, A., Pradono, M.H. and Kalantari A. (2006), "Negative stiffness friction damping for seismically isolated structures", Struct. Control Health Monit., 13(2-3), 775-791.
  17. Iemura, H. and Pradono, M.H. (2009), "Advances in the development of pseudo-negative-stiffness dampers for seismic response control", Struct. Control Health Monit., 16(7-8), 784-799.
  18. Irvine, H.M. (1981), Cable Structures, Cambridge, MA, U.S.A., MIT Press.
  19. Johnson, E., Baker, G., Spencer, B. and Fujino, Y. (2007), "Semiactive damping of stay cables", J. Eng. Mech. - ASCE, 133(1), 1-11.
  20. Johnson, E.A., Christenson, R.E. and Spencer Jr., B.F. (2003), "Semiactive damping of cables with sag", Comput. - Aided Civil Infrastruct. E., 18(2), 132-146.
  21. Kovacs, I. (1982), "Zurfrage der seilschwingungen und der seildampfung", Bautechnik, 59(10), 325-332.
  22. Krenk, S. (2000), "Vibrations of a taut cable with an external damper", J. Appl. Mech. - T. ASME, 67(4), 772-776.
  23. Krenk, S. and Hogsberg, J. (2014), "Tuned mass absorber on a flexible structure", J. Sound Vib., 333(6), 1577-1595.
  24. Krenk, S. and Hogsberg, J.R. (2005), "Damping of cables by a transverse force", J. Eng. Mech. - ASCE, 131 (4), 340-348.
  25. Krenk, S. and Nielsen, S.R.K. (2002), "Vibrations of a shallow cable with a viscous damper", P. Roy. Soc. Lond., Series A, 458(2018), 339-357.
  26. Kumarasena, S., Jones, N.P., Irwin, P. and Taylor P. (2007), Wind-Induced Vibration of Stay Cables, Report.
  27. Li, H., Liu, M. and Ou, J. (2008), "Negative stiffness characteristics of active and semi-active control systems for stay cables", Struct. Control Health Monit., 15(2), 120-142.
  28. Main, J.A. (2002), Modeling the vibrations of a stay cable with attached damper, Ph.D. Dissertation, Johns hopkins University, Baltimore, Maryland.
  29. Main, J.A. and Jones, N.P. (2002a), "Free vibrations of taut cable with attached damper. I: Linear viscous damper", J. Eng. Mech. - ASCE, 128(10), 1062-1071.
  30. Main, J.A. and Jones, N.P. (2002b), "Free vibrations of taut cable with attached damper. II: Nonlinear damper", J. Eng. Mech. - ASCE, 128(10), 1072-1081.
  31. Main, J.A. and Jones, N.P. (2007a), "Vibration of tensioned beams with intermediate damper. I: Formulation, influence of damper location", J. Eng. Mech. - ASCE, 133(4), 369-378.
  32. Main, J.A. and Jones, N.P. (2007b), "Vibration of tensioned beams with intermediate damper. II: Damper near a support", J. Eng. Mech. - ASCE, 133(4), 379-388.
  33. Main, J.A. and Krenk, S. (2005), "Efficiency and tuning of viscous dampers on discrete systems", J. Sound Vib., 286(1-2), 97-122.
  34. Nagarajaiah, S. (2009), "Adaptive passive, semiactive, smart tuned mass dampers: identification and control using empirical mode decomposition, Hilbert transform, and short-term fourier transform", Struct. Control Health Monit., 16(7-8), 800-841, DOI: 10.1002/stc.349.
  35. Ou, J. and Li, H. (2010), "Analysis of capability for semi-active or passive damping systems to achieve the performance of active control systems", Struct. Control Health Monit., 17(7), 778-794.
  36. Pacheco, B.M., Fujino, Y. and Sulekh, A. (1993), "Estimation curve for modal damping in stay cables with viscous damper", J. Struct. Eng. - ASCE, 119(6), 1961-1979.
  37. Pasala, D., Sarlis, A., Nagarajaiah, S., Reinhorn, A., Constantinou, M. and Taylor, D. (2013), "Adaptive negative stiffness: New structural modification approach for seismic protection", J. Struct. Eng. - ASCE, 139(7), 1112-1123, DOI: 10.1061/(ASCE)ST.1943-541X.0000615.
  38. Pasala, D., Sarlis, A., Reinhorn, A., Nagarajaiah, S., Constantinou, M. and Taylor, D. (2014), "Simulated bilinear-elastic behavior in a SDOF elastic structure using negative stiffness device: Experimental and analytical study", J. Struct. Eng. - ASCE, 140(2), 04013049.
  39. Sarlis, A., Pasala, D., Constantinou, M., Reinhorn, A., Nagarajaiah, S. and Taylor, D. (2013), "Negative stiffness device for seismic protection of structures", J. Struct. Eng. - ASCE, 139(7), 1124-1133.
  40. Spencer, B. and Nagarajaiah, S. (2003), "State of the art of structural control", J. Struct. Eng. - ASCE, 129 (7), 845-856.
  41. Sun, C. and Nagarajaiah, S. (2014), "Study on semi-active tuned mass damper with variable damping and stiffness under seismic excitations", Struct. Control Health Monit., 21(6), 890-906.
  42. Sun, C., Nagarajaiah, S. and Dick, A. (2014), "Family of smart tuned mass dampers with variable frequency under harmonic excitations and ground motions: closed-form evaluation", Smart Struct. Syst., 13(2), 319-341.
  43. Sun, L. and Huang, H. (2008), Design, implementation and measurement of cable dampers for large cable-stayed bridges, IABSE Congress Report, 17(16), 242-243.
  44. Sun, L. and Chen, L. (2015), "Free vibrations of a taut cable with a general viscoelastic damper modeled by fractional derivatives", J. Sound Vib., 335(2015), 19-33.
  45. Sun, L., Shi, C., Zhou, H. and Cheng, W. (2004), "A full-scale experiment on vibration mitigation of stay cable", Proceedings of the IABSE Symp. Rep., IABSE Symp., Shanghai 2004: Metropolitan Habitats and Infrastructure, IABSE, Zurich, Switzerland.
  46. Tabatabai, H. and Mehrabi, A.B. (2000), "Design of mechanical viscous dampers for stay cables", J. Bridge Eng., 5(2), 114-123.
  47. Weber, F. and Boston, C. (2011), "Clipped viscous damping with negative stiffness for semi-active cable damping", Smart Mater. Struct., 20(4), 045007.
  48. Weber, F., Boston, C. and Maslanka, M. (2011), "An adaptive tuned mass damper based on the emulation of positive and negative stiffness with an MR damper", Smart Mater. Struct., 20(1), 015012.
  49. Xu, Y.L. and Yu, Z. (1998), "Vibration of inclined sag cables with oil dampers in cable-stayed bridges", J. Bridge Eng., 3(4), 194-203.
  50. Xu, Y.L., Yu, Z. and Ko, J.M. (1998), "Forced vibration studies of sagged cables with oil damper using a hybrid method", Eng. Struct., 20(8), 692-705.
  51. Zhou, H., Sun, L. and Xing, F. (2014a), "Damping of full-scale stay cable with viscous damper: Experiment and analysis", Adv. Struct. Eng., 17(2), 265-274.
  52. Zhou, H., Sun, L. and Xing, F. (2014b), "Free vibration of taut cable with a damper and a spring", Struct. Control Health Monit., 21(6), 996-1014.

피인용 문헌

  1. Experimental investigation on a passive auto-tuning mass damper for vibration control 2017,
  2. Inertial mass damper for mitigating cable vibration vol.24, pp.10, 2017,
  3. Free vibration and damping of a taut cable with an attached viscous mass damper 2017,
  4. Performance Comparison between Passive Negative-Stiffness Dampers and Active Control in Cable Vibration Mitigation vol.22, pp.9, 2017,
  5. Semi-active damping with negative stiffness for multi-mode cable vibration mitigation: approximate collocated control solution vol.24, pp.11, 2015,
  6. Soil-Structure Interaction for Integrated Design of Weakened and Damped Structures vol.11, pp.04, 2017,
  7. Development of a Self-Powered Magnetorheological Damper System for Cable Vibration Control vol.8, pp.1, 2018,
  8. Steady-State Analysis of Cable with Nonlinear Damper via Harmonic Balance Method for Maximizing Damping vol.143, pp.2, 2017,
  9. Cable vibration control with both lateral and rotational dampers attached at an intermediate location vol.377, 2016,
  10. Residual mode correction in calibrating nonlinear damper for vibration control of flexible structures vol.406, 2017,
  11. Cables interconnected with tuned inerter damper for vibration mitigation vol.151, 2017,
  12. Modeling and control performance of a negative stiffness damper for suppressing stay cable vibrations vol.23, pp.4, 2016,
  13. Free vibration of a taut cable with a damper and a concentrated mass vol.25, pp.11, 2018,
  14. Refined damper design formula for a cable equipped with a positive or negative stiffness damper vol.25, pp.10, 2018,