Combustion Properties of Major Wood Species Planted in Indonesia

인도네시아 주요 조림수종의 연소특성

  • Park, Se-Hwi (College of Forest & Environmental Sciences, Kangwon National University) ;
  • Jang, Jae-Hyuk (College of Forest & Environmental Sciences, Kangwon National University) ;
  • Hidayat, Wahyu (College of Forest & Environmental Sciences, Kangwon National University) ;
  • Qi, Yue (College of Forest & Environmental Sciences, Kangwon National University) ;
  • Febrianto, Fauzi (Faculty of Forestry, Bogor Agricultural University) ;
  • Kim, Nam-Hun (College of Forest & Environmental Sciences, Kangwon National University)
  • 박세휘 (강원대학교 산림환경과학대학) ;
  • 장재혁 (강원대학교 산림환경과학대학) ;
  • ;
  • ;
  • ;
  • 김남훈 (강원대학교 산림환경과학대학)
  • Received : 2015.07.06
  • Accepted : 2015.08.19
  • Published : 2015.11.25


This study was performed to understand combustion properties four major Indonesian wood species such as Albizia, Gmelina, Mangium and Mindi were investigated by cone-calorimeter for better utilization of theses wood species. Heat release rate (HRR), total heat release (TSR), specific mass loss rate (SMLR), effective heat of combustion (EHC), time to ignition (TTI), flame time (FT), specific extinction area (SEA), smoke production rate (SPR) and CO compound production rate were measured. HRR, THR and FT were proportional to the density of woods. Albizia showed the highest HRR, while Mindi had the lowest HRR. For SPR, Albizia showed the highest value due to its higher SEA. On the other hand, Mindi had the lowest SPR due to a lower SEA value. The highest smoke emission was for Albizia at the beginning of combustion. After 300 seconds, smoke emission of Gmleina and Mangium was increased greatly. Mangium and Mindi showed the highest total carbon dioxide emission. Expecially, Gmelina released the highest carbon monoxide during the combustion period and presented three times higher $CO/CO_2$ ratio than those of other species due to incomplete combustion.


Supported by : 산림청


  1. Audeber M., Dhima D., Taazount M., Bouchair, A. 2013. Thermo-mechanical behaviour of timber-to-tiber conections exposed to fire. Fire Safety Journal 56: 52-64.
  2. Babrauskas, V. 1984. Development of cone calorimeter: A bench-scale consumption. Fire and Materials 8(2): 81-95.
  3. Babrauskas, V., Grayson, S.J. 1992. Heat release in fires. E&FN Spon (Chapman and Hall), London, UK.
  4. Baysal, E., Altinok, M., Colak, M., Ozaki, S.K., Toker, H. 2007. Fire Resistance of Douglas fir (Psedotuga menzieesi) treated with borates and natural extractives. Bioresources Technology 98: 1101-1105.
  5. Brostow W., Menard K., Menard, N. 2009. Combustion properties of several species of wood. Chemistry & Chemical Technology 3(3): 173-176.
  6. Choi, J.M. 2011. A study on combustion characteristics of fire retardant treated Pinus densiflora and Pinus koraiensis. Journal of the Korean Wood Science and Technology 39(3): 244-251.
  7. Chun, Y.J., Jin, E. 2010. Combustion characteristics of the Pinus rigida and Castanea savita dried at room temperature. Journal of Korean Institute of Fire Science and Engineering 24(3): 86-92.
  8. Drysdale D. 1996. An introduction to fire dynamics. john Wily & Sons, USA.
  9. Hull R.T. and Paul K.T. 2007. Bench-scale assessment of combustion toxicity - a critical analysis of current protocols. Fire safety Journal 42(5): 340-365.
  10. Jang, S.R., Jang, J.H., Kim, J.H., Febrianto, F., Kim, N.H. 2014. Anatomical characteristics of major plantation species growing in Indonesia II. Journal of the Korean Wood Science and Technology 42(6): 635-645.
  11. Kim, C.J., Masataka, A., Kang, K.K. 1999. Combustion characteristics of wood chips (II)- Flame shape of combustion and ignition delay. Journal of the Korean Society of Industrial Application 2(2): 139-146.
  12. Kim, J.H., Jang, J.H., Kwon, S.M., Febrianto, F. Kim, N.H. 2012. Anatomical properties of major planted and promising species growing in Indonesia. Journal of the Korean Wood Science and Technology 40(4): 244-256.
  13. Kim, J.H., Jang, J.H., Ryu, J.Y., Febrianto, F., Hwang, W.J., Kim, N.H. 2014. Physical and mechanical properties of major plantation and promising tree species grown in Indonesia(I). Journal of the Korean Wood Science and Technology 42(4): 467-476.
  14. Korean Agency for Technology and Standard. 2006. Reaction to fire test-Heat release, smoke production and mass loss late - Part 1 : Heat release rate(Cone calorimeter method). KS F ISO 5660-1.
  15. Park S.B., Park, J.S. 2012. Combustion characteristics of bamboo charcoal boards. Journal of the Korean Wood Science and Technology 40(1): 19-25.
  16. Pearce, F.M., Khanna, Y.P., Raucher, D. 1981. Thermal analysis in polymer flammability. Chapter 8: Thermal characterization of polymeric materials. Academic press. New York. USA.
  17. Quintiere, J.G. 1992. A semi-quantitative model for the burning rate of solid materials. NISTIR 4840, National institute of standards and technology, Gaithersburg, MD.
  18. Ragland. K.W. and Aerts D.J. 1991. Properties of wood for combustion analysis. Bioresource Technology 37: 161-168.
  19. Shafizadeh, F., Degroot, W.F. 1976. Combustion characteristics of cellulosic fuels in : Tillman, thermal uses and properties of carbohydrates and lignins. Academic press. New York, USA.
  20. Son, D.W. and Kang, S.G. 2014. Combustion Properties of Woods for Indoor Use (I). Journal of the Korean Wood Science and Technology 42(6): 675-681.
  21. Son, D.W., Kang, M.R., Son, S.W., So, I.S., Park, S.B. 2014. Comparison of combustion characteristics of woods used in indoor. Proc. of 2014 Annual Meeting of The Korean Society of Wood Science and Technology. Cheong-Ju, Republic of Korea. pp. 348-349.
  22. Tran, H.C., White, R.H. 1992. Burning rate of solid wood measured in a heat release calorimeter. Fire and Materials 16: 197-206.