Go to the main menu
Skip to content
Go to bottom
REFERENCE LINKING PLATFORM OF KOREA S&T JOURNALS
> Journal Vol & Issue
International Journal of Fluid Machinery and Systems
Journal Basic Information
Journal DOI :
Korean Fluid Machinery Association
Editor in Chief :
Franois Avellan / Kwang-Yong Kim / Yoshinobu Tsujimoto / Yulin Wu
Volume & Issues
Volume 3, Issue 4 - Dec 2010
Volume 3, Issue 3 - Sep 2010
Volume 3, Issue 2 - Jun 2010
Volume 3, Issue 1 - Mar 2010
Selecting the target year
Unsteady Swirling Flows Arising in Straight Tubes
Tsurusaki, Hiromu ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 211~220
DOI : 10.5293/IJFMS.2010.3.3.211
The objective of this study is to clarify the occurrence of the high-speed mode of unsteady swirling flows in straight tubes. The unsteady flows generated in the tube were measured by means of a semiconductor-type pressure transducer and an FFT analyzer. The high-speed mode measured has rotational speed which is approximately equal to or higher than the peripheral velocity of the swirling flow. The unsteady flow is due to cell rotation in the circumferential direction of the tube. The occurrence of the high-speed mode was confirmed, and the characteristics (rotational speed, pressure amplitude, and phase) of this mode were clarified. In order to understand the measured unsteady flows, the three dimensional vortex core profiles were discussed based on the distributions of the pressure amplitude and phase.
Numerical Study on Mixing Performance of Straight Groove Micromixers
Hossain, Shakhawat ; Kim, Kwang-Yong ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 227~234
DOI : 10.5293/IJFMS.2010.3.3.227
Numerical analyses have been performed to investigate the effects of geometric parameters of a straight groove micromixer on mixing performance and pressure drop. Three-dimensional Navier-Stokes equations with two working fluids, water and ethanol have been used to calculate mixing index and pressure drop. A parametric study has been carried out to find the effects of the number of grooves per cycle, arrangement of patterned walls, and additional grooves in triangular dead zones between half cycles of grooves. The three arrangements of patterned walls in a micromixer, i.e., single wall patterned, both walls patterned symmetrically, and both walls patterned asymmetrically, have been tested. The results indicate that as the number of grooves per cycle increases the mixing index increases and the pressure drop decreases. The microchannel with both walls patterned asymmetrically shows the best mixing performance among the three different arrangements of patterned walls. Additional grooves confirm the better mixing performance and lower pressure drop.
Moment Whirl due to Leakage Flow in the Back Shroud Clearance of a Rotor
Tsujimoto, Yoshinobu ; Ma, Zhenyue ; Song, Bing-Wei ; Horiguchi, Hironori ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 235~244
DOI : 10.5293/IJFMS.2010.3.3.235
Recent studies on the moment whirl due to leakage flow in the back shroud clearance of hydro-turbine runners or centrifugal pump impellers are summarized. First, destabilizing effect of leakage flow is discussed for lateral vibrations using simplified models. Then it is extended to the case of whirling motion of an overhung rotor and the criterion for the instability is obtained. The fluid moment caused by a leakage clearance flow between a rotating disk and a stationary casing was obtained by model tests under whirling and precession motion of the disk. It is shown that the whirl moment always destabilizes the whirl motion of the overhung rotor while the precession moment destabilizes the precession only when the precession speed is less than half the rotor speed. Then vibration analyses considering both whirl and precession are made by using the hydrodynamic moments determined by the model tests. For larger overhung rotors, the whirl moment is more important and cause whirl instability at all rotor speed. On the other hand, for smaller overhung rotors, the precession moment is more important and cancels the destabilizing effect of the whirl moment.
Air-Water Two-Phase Flow Performances of Centrifugal Pump with Movable Bladed Impeller and Effects of Installing Diffuser Vanes
Sato, Shinji ; Furukawa, Akinori ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 245~252
DOI : 10.5293/IJFMS.2010.3.3.245
It's known that pump head of centrifugal impeller with lager blade outlet angle is kept higher in air-water two phase flow condition, though the efficiency in water single phase flow condition is inferior. In the present study, a centrifugal impeller with variable blade outlet angles, that has higher efficiencies in both water single phase flow and air-water two phase flow conditions, is proposed. And the performances of the centrifugal impeller with variable blade outlet angles were experimentally investigated in both flow conditions of single and two-phase. In addition, effects of installing diffuser vanes on the performances of centrifugal pump with movable bladed impeller were also examined. The results are as follows: (1) The movable bladed impeller that proposed in this study is effective for higher efficiency in both water single phase and air-water two phase flow conditions. (2) When diffuser vanes are installed, the efficiency of movable bladed impeller decreases particularly at large water flow rate in water single-phase flow condition; (3) The performances of movable bladed impeller are improved by installing of diffuser vanes in air-water two-phase flow condition at relatively small water rate. The improvement by installing of diffuser vanes however disappears at large water flow rate.
Investigation of Leakage Characteristics of Straight and Stepped Labyrinth Seals
Kim, Tong-Seop ; Kang, Soo-Young ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 253~259
DOI : 10.5293/IJFMS.2010.3.3.253
Leakage characteristics of two labyrinth seals with different configurations (straight vs stepped) were investigated. Leakage flows were predicted by computational fluid dynamics (CFD) for the two configurations and compared with test data. A semi-analytical leakage prediction tool was also tried to predict the leakage. It was confirmed that the CFD gives quite good agreements with test data. The analytical tool also yielded similar leakage behaviors with test results, but the overall agreement with test data was not as good as that of the CFD. The effect of flow direction in the stepped seal on leakage flow was examined. The dependence of leakage performance, in terms of flow function, on the seal clearance size was investigated. Flow function decreased with decreasing clearance in the straight seal, while the trend was reversed in the stepped seal.
Study of the Flow in Centrifugal Compressor
Xu, Cheng ; Amano, Ryoichi Samuel ;
International Journal of Fluid Machinery and Systems, volume 3, issue 3, 2010, Pages 260~270
DOI : 10.5293/IJFMS.2010.3.3.260
Reducing the losses of the tip clearance flow is one of the keys in an unshrouded centrifugal compressor design and development because tip clearances are large in relation to the span of the blades and also centrifugal compressors produce a sufficiently large pressure rise in single stage. This problem is more acute for a low flow high-pressure ratio impeller design. The large tip clearance would cause flow separations, and as a result it would drop both the efficiency and surge margin. Thus a design of a high efficiency and wide operation range low flow coefficient centrifugal compressor is a great challenge. This paper describes a recent development of high efficiency and wide surge margin low flow coefficient centrifugal compressor. A viscous turbomachinery optimal design method developed by the authors for axial flow machine was further extended and used in the centrifugal compressor design. The compressor has three main parts: impeller, a low solidity diffuser and volute. The tip clearance is under a special consideration in this design to allow impeller insensitiveness to the clearance. A patented three-dimensional low solidity diffuser design method is used and applied to this design. The compressor test results demonstrated to be successful to extend the low solidity diffusers to high-pressure ratio compressor. The compressor stage performance showed the total to static efficiency of the compressor being about 85% and stability range over 35%. The test results are in good agreement with the design.