Go to the main menu
Skip to content
Go to bottom
REFERENCE LINKING PLATFORM OF KOREA S&T JOURNALS
> Journal Vol & Issue
Journal of ILASS-Korea
Journal Basic Information
Journal DOI :
Institute for Liquid Atomization and Spray Systems-Korea
Editor in Chief :
Volume & Issues
Volume 14, Issue 4 - Dec 2009
Volume 14, Issue 3 - Sep 2009
Volume 14, Issue 2 - Jun 2009
Volume 14, Issue 1 - Mar 2009
Selecting the target year
A Numerical Study of
Efficiency Improvement in the DSI process of FGD
Chung, J.D. ; Kim, J.W. ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 1~7
This study carried out numerical analysis of flow field of combustion gas and sorbent to test sorbent efficiency of DSI process. To provide rapid mixing for increase utilization rate of sorbent, streamwise vorticity can be introduced into the flowing streams by other means; for example, by installing vortex generators immediately downstream of the wavy trailing edge. Computing results show that the degree of sorbent dispersion depends strongly on duct structure. Highest dispersion efficiency received when vortex generator was installed inside of duct. The results presented in this study a optimum condition for the development of practical DSI process.
Effect of Injection Condition on the Diesel. Fuel Atomization in a Multi-Hole Nozzle
Sub, Hyun-Kyu ; Kim, Jee-Won ; Lee, Chang-Sik ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 8~14
This paper present the diesel fuel spray evolution and atomization performance in a multi-hole nozzle in terms of injection rate, spray evolutions, and mean diameter and velocity of droplets in a compression ignition engine. In order to study the effect of split injection on the diesel fuel spray and atomization characteristic in a multi-hole nozzle, the test nozzle that has two-row small orifice with 0.2 mm interval was used. The time based fuel injection rate characteristics was analyzed from the pressure variation generated in a measuring tube. The spray characteristics of a multi-hole nozzle were visualized and measured by spray visualization system and phase Doppler particle analyzer (PDPA) system. It was revealed that the total injected fuel quantities of split injection are smaller than those of single injection condition. In case of injection rate characteristics, the split injection is a little lower than single injection and the peak value of second injection rate is lower than single injection. The spray velocity of split injection is also lower because of short energizing duration and small injection mass. It can not observe the improvement of droplet atomization due to the split injection, however, it enhances the droplet distributions at the early stage of fuel injection.
An Investigation of Performance Change of Diesel Oxidation Catalyst for Diesel Vehicle
Hwang, Jin-Woo ; Lee, Chang-Sik ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 15~19
This paper is to investigated the analysis of performance characteristics of diesel oxidation catalyst (DOC) for diesel vehicle with 2.5L piston displacement. The performance evaluation test of DOC applied to test diesel vehicle was carried out for four kinds of DOCs manufactured from different company. The testing DOCs were randomly selected from the retrofit vehicle and then standard test vehicle that was representative for the application group was equipped with DOC for the test. In this verification test, the reduction rate of particulate matter (P.M.) and the deviation of the performance of the DOC were examined through CVS-75 mode of the standard vehicle and SOF reduction rate of specific DOC was investigated. It was found that some DOCs failed to pass the criteria of the P.M. reduction rate because of the reason seen catalyst aging even if they were same devices. In the result of SOF analysis, the specific DOC showed more PM reduction than SOF of PM. reduction exceptionally.
Cooling Effect of a Heated Porous Plate by Droplets Impingement - A Preliminary Study
Ryu, S.U. ; Kim, W.S. ; Lee, S.Y. ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 20~27
In the present work, effects of spray characteristics (droplet size and velocity) on the temperature variation of a heated porous plate (Melamine foam) have been investigated through a series of experiments. Based on the measured data, time required to cool down the hot porous material turned out to be shorten by doing with the smaller droplet size and/or smaller impinging velocity. In particular, the droplet size effect is more prominent than the impinging velocity. The cooling performance in the porous material is directly proportional to the penetration velocity.
Comparison of Performance and Emissions Characteristics on 23cc Gasoline engine and LPG engine at WOT Condition
Kim, B.G. ; Choi, Y.H. ; Oh, J.W. ; Lee, D.G. ; Kim, D.S. ; Yoon, S.J. ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 28~33
This paper presents the performance and emissions characteristics of a small spark-ignited 2-stroke gasoline and LPG engine. The engine used in this paper is a single cylinder, two-stroke, air-cooled SI engine for brush cutter. We measured the rpm, torque, fuel consumption and HC, CO, NOx emissions in associated with the dynamometer load at WOT. The results showed that as engine revolution speed decreased, the excess air ratio of gasoline engine kept going about 0.9 and that of LPG engine increased 0.83 to 1.05. Torque and power of gasoline engine was higher than LPG engine. In exhaust emissions, HC emissions of gasoline engine was lower than LPG engine. In low speed area, CO emissions of LPG engine was lower than gasoline engine. Both gasoline engine and LPG engine emitted little NOx emissions.
Characteristics of Pressure wave Pulsation at Carburetor on Small SI Engine
Oh, J.W. ; Choi, Y.H. ; Kim, B.G. ; Lee, D.G. ; Kim, D.S. ; Yoon, S.J. ;
Journal of ILASS-Korea, volume 14, issue 1, 2009, Pages 34~38
This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.