• 제목, 요약, 키워드: Cylinder contact

검색결과 156건 처리시간 0.046초

클러치 마스터실린더 주 컵-시일의 유한요소해석 (Finite Element Analysis of Primary Cup-Seal in a Clutch Master Cylinder)

  • 임문혁;이재천;구본은
    • 한국자동차공학회논문집
    • /
    • v.10 no.3
    • /
    • pp.143-150
    • /
    • 2002
  • The characteristics of rubber cup seal is highly nonlinear due to the nature of the material's non-linearity and large deformation with frictional contact. And the performance of sealing in master cylinders of automobile is one of the most important factors which affects the safety of drivers. The effects of various shape of the primary cup seal in clutch master cylinder was investigated to reduce oil leakage and to obtain a long reliable life. Deformation and distribution of stresses on the primary cup seal against hydraulic oil pressure were analyzed with changing design parameters such as depth and radius in cup-seal. The obtained results indicate that the depth of cup seal plays a major role on deformation resulting in the sealing force to the wall of clutch master cylinder.

플라즈마용사 세라믹코팅의 실린더라이너 적용위한 마찰 마모특성 연구 (Tribological Behaviour of Plasma Sprayed Ceramic Coatings for the Application to the Cylinder Linerin Engines)

  • 안효석;김장엽;임대순
    • 한국자동차공학회논문집
    • /
    • v.1 no.2
    • /
    • pp.89-102
    • /
    • 1993
  • In this experimental investigation, various plasma-sprayed zirconia contained coatings and a kind of alumina-zirconia coating were studied to gain a better understanding of their tribological behaviour under dry contact condition in a reciprocating motion at temperature of 200℃. Particular attention was made for finding appropriate coatings in cylinder liner/piston ring application with an emphasis on the antiwear property. In order to identify the wear mechanism, SEM(Scanning Electron Microscope), optical micrograph, and roughness tester were used. Alumina-zirconia and 8% yttria-zirconia were found to be most appropriate for the application to the cylinder liner/piston ring and, especially, alumina-zirconia exhibited highest wear-resistance and also showed good friction characteristics. Wear mechanisms of ceramic coatings identified.

  • PDF

중형 디젤엔진용 실린더 프레임에 대한 구조해석 (Structural Analysis of Cylinder Frame for Medium-speed Diesel Engine)

  • 손정호;김무승;안성찬
    • 한국마린엔지니어링학회:학술대회논문집
    • /
    • /
    • pp.144-148
    • /
    • 2005
  • Cylinder frame manufactured by casting is assembled with the components such as cylinder head, cylinder liner and main bearing cap, etc. The mechanical contact between all of the neighboring components due to bolt tightening was taken into consideration. The loads used in structural analysis were the bolt tightening forces induced by hydraulic jack and the dynamic forces calculated from kinematic analysis. The difference of forces between the neighboring cylinders was taken into account. The maximum stress, stress amplitude and mean stress calculated from the results of structural analyses were used to evaluate the static and fatigue strength. Gray cast iron which is material of cylinder frame has the material characteristics of very small elongation and different strength in tension and compression. Based on such an material characteristics, the strength evaluation of cylinder frame was carried out with in-house program developed internally.

  • PDF

대형 2행정 디젤기관에 있어서 전자제어 퀼 부착 모터구동 실린더 주유기의 송출유량 특성에 관한 연구 (A Study on Feed Rate Characteristics of Motor-driven Cylinder Lubricator with Electronic Control Quill in a Large Two-stroke Diesel Engine)

  • 배명환;정화;정연학;김인덕;강창호
    • 한국자동차공학회논문집
    • /
    • v.15 no.6
    • /
    • pp.1-8
    • /
    • 2007
  • Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke marine diesel engine is of great economic importance. In Korea, authors first developed a motor-driven cylinder lubricator for a Wartsila Switzerland large two-stroke diesel engine. The characteristic of the developed product is that can control automatically the oil feed rate with a load fluctuation by the motor drive and the offset cam. For manufacturing the reliable and useful products, however, it is necessary to investigate further characteristics and to improve performances as a cylinder lubricator. In this study, the effects of pump motor speed, plunger stroke and cylinder back pressure on oil feed rate, maximum discharge and delivery pressures are experimentally investigated by using the electronically controlled quill injection system and distributer in the developed cylinder lubricator. It is found that the oil feed rates of electronic control and mechanical type quills with the in-cylinder back pressure are differently characterized by the role of accumulator, the viscous resistance of contact area, etc. It can be also shown that the maximum discharge pressure of the electronic control quill is lower than the mechanical type one but the maximum discharge pressure difference of two types decreased as plunger stroke is small, and the maximum delivery pressures of two types increased as plunger stroke, motor speed and back pressure are elevated but the maximum delivery pressure of mechanical type is higher than the one of electronic control type.

치면 프로파일 모델에 따른 기어 치면 내부의 응력 분포 (Sub­surface Stress Distribution beneath the Contact Surface of the Gear Teeth for Two Profile Models)

  • 구영필;오명석;김형자;김영대
    • Tribology and Lubricants
    • /
    • v.19 no.6
    • /
    • pp.357-364
    • /
    • 2003
  • The sub­surface stress field beneath the gear's contact surface caused by the contact pressure in lubricated condition has been calculated. To evaluate the influence of the clearance shape on the stress field, two kinds of tooth profile models were chosen. One is the conventional cylinder contact model and the other is the new numerical model. Love's rectangular patch solution was used to obtain the sub­surface stress field. The analysis results show that the sub­surface stress is quite dependent on both the contact pressure and the profile model. The maximum effective stress of the new model is lower than that of the old model. The depth where the maximum effective stress occurs in the new model is not proportional to the intensity of the external load.

홀로그래픽 간섭법을 이용한 진동모드의 계측에 관한 연구 (A Study on the Measurement of Vibration Mode Shape using Holographic interferometry)

  • 김광래
    • 한국생산제조학회지
    • /
    • v.9 no.3
    • /
    • pp.130-135
    • /
    • 2000
  • In this study the vibration behavior of the stiffened double cylinder was experimently analyzed. Due to the complex structure of the double cylinder the outside cylinder frequency responses to the exciting forces applied on various posi-tions were analyzed by using spectrum analyzer in conjunction with an accelerometer and the natural frequencies were obtained. The technique of time-averaged holographic interferometry is applied to study the vibration characteristics of outside cylinder with stiffening T frame. The experimental data showed that the T frame had salient effect of damping on the testing structure at most of resonances. however the experimental results also revealed interesting phenomenon. At some particular frequencies the T frame. The experimental data showed that the T frame had salient effect of damping on the testing structure at most of resonances. However the experimental results also revealed interesting phenomenon. At some particular frequencies the T frame seemed to behave as a transmitter. In addition it has been successfully demon-started that optical method such as holographic interferometry is well suited for the identification of mode shapes. They can give us a whole-field non-contact measurement instead of the point-wise measurement by accelerometer in classical modal testing.

  • PDF

실린더형 정전용량 센서 및 변위 측정시스템 설계 (Design of Stroke Measurement System and Cylinder-type Capactive Sensor)

  • 이재건;이인곤;박성균;홍익표
    • 한국정보통신학회:학술대회논문집
    • /
    • /
    • pp.910-912
    • /
    • 2015
  • 본 논문에서는 중장비나 댐의 수문 등의 적용된 유압 실린더의 변위(stroke)를 검출하여 유압 실린더의 정밀제어 또는 자동화를 위한 정전용량 센서(Capacitive Sensor) 및 변위 검출 시스템을 설계하였다. 기존 실린더의 변위 검출 방식인 코일을 이용한 자기장 센서, LVDT 센서 등은 높은 정확도에 비해 충격 및 진동 완화 또는 센서 보호 하우징(Housing) 등 부수적인 설비에 따른 높은 비용, 큰 부피와 같은 문제가 있다. 따라서 이러한 개선하기 위해 유압 실린더 내의 직접 적용되어 실린더의 변위 검출이 가능한 정전용량 센서를 설계하였으며, 설계한 정전용량 센서를 통하여 실린더의 변위에 따른 커패시턴스 값을 검출하여 실린더 위치 측정이 가능한 시스템을 설계 및 검증 하였다.

  • PDF

유한요소법을 이용한 실린더 라이너의 변형과 응력에 관한 연구 (The use of finite element techniques for the deformation and stress of cylinder liner)

  • 오성환;조원행
    • 오토저널
    • /
    • v.7 no.1
    • /
    • pp.55-62
    • /
    • 1985
  • This study modeled in axisymmetric solid elements and analyzed the neighbourhood of the contact surface zone between liner and block in a diesel engine. The results of finite element analysis show that this model is deformed by bolt jointed load and pressure load and that stresses can vary much due to major dimensional changes in the joint area. Guidelines have been developed for selecting fillet radii and for the width of the contact area between liner and block.

  • PDF

피스톤 런닝부의 소재에 따른 마모특성 연구 (A Study on Wear Characteristics of Piston Running Part)

  • 장정환;이혜경;주병돈;이재호;문영훈
    • 한국소성가공학회:학술대회논문집
    • /
    • /
    • pp.375-378
    • /
    • 2007
  • Abrasive wear between piston ring face and cylinder liner is an extremely unpredictable and hard-to-reproduce phenomenon that significantly decreases engine performance. Wear by abrasion are forms of wear caused by contact between a particle and solid material. Abrasive wear is the loss of material by the passage of hard particles over a surface. From the pin-on-disk test, particle dent test and scuffing test, abrasive wear characteristics of diesel engine cylinder liner-piston ring have been investigated. Pin-on-disk test results indicate that abrasive wear resistance is not simply related to the hardness of materials, but is influenced also by the microstructure, temperature, lubricity and micro- fracture properties. In particle dent test, dent resistance stress decreases with increasing temperature. From the scuffing test by using pin-on-disk tester, scuffing mechanisms for the soft coating and hard coating were proposed and experimentally confirmed.

  • PDF