Journal of the Korean Ceramic Society (한국세라믹학회지)

The Korean Ceramic Society (한국세라믹학회)
권호 표지

The Effects of SiO2 Addition and Cooling Rate Change by Sol-gel Processing in Semiconducting BaTiO3 Ceramics

반도성 $BaTiO_3$ 세라믹스의 Sol-gel법에 의한 $SiO_2$ 첨가 및 냉각속도 효과

  • 권오성 (명지대학교 공과대학 무기재료공학과) ;
  • 정용선 (한양대학교 세라믹소재연구소) ;
  • 윤영호 (삼화콘덴서 공업(주)) ;
  • 이병하 (명지대학교 공과대학 무기재료공학과)
  • Published : 1996.12.01
Download PDF
⟨ Previous Next ⟩

Abstract

Generally it requires high sintering temperatures more than 135$0^{\circ}C$ to make semiconductive BaTiO3 ceramics. Also it is very difficult to achieve a homogeneous mixing in solid-state reaction method. Therefore the liquid phase distributed to non-uniform dilute the characteristics of PTCR. In order to improve the uniformity this study is used the sol-gel coating method. Using this method we studied the new manufacturing process that had a high reproducibility and mass production capability. Tetraethyl orthosilicate (TEOS) was used as a source of Si. The semiconductive BaTiO3 ceramics which was produced by sol-gel method for the SiO2 addition and sintered between 124$0^{\circ}C$ and 130$0^{\circ}C$ showed almost same resistivity at room temperature among 125$0^{\circ}C$ and 130$0^{\circ}C$. As the results We could be sintered the semiconducting BaTiO3 ceramics at lower temperature even at 125$0^{\circ}C$ maintaining the same specific resistivity ratio ($\rho$max/$\rho$min) at 130$0^{\circ}C$. The specific resistivity both below and above the Curie temperature were increased by slow cooling and the steepness of the plots in the reasion of transition from low to high resistance increased as the cooling rate decreased.

Keywords

References

  1. Ceram.Bull v.47 no.2 Semiconducting BaTiO₃with Addition of Al₂O₃,SiO₂and TiO₂ Y. Matsuo;M. FuJimura;H. Sasaki;K. Negase;S. Hayakawa
  2. Proc British Ceram Soc v.18 The Effect of Silica Addition on the Semiconducting Properties of Doped Barium Titanate C. Eastman;C.A. Elyard;D. Warren
  3. J.Am.Ceram Soc v.54 no.9 Exaggerated Grain Growth in Liquid Phase Sintering of BaTiO₃ Y. Matsuo;H. Sasaki
  4. J. Inst. Electron. Commun Eng Japan v.55-C no.3 Formation of BaTiO₃ Ceramics Semiconducting Layer by Diffusion T. Fukami
  5. Japan J. Appl Phys v.18 no.4 Dependence of Resistivity on Donor Dopant Content in Barium Titanate Ceramics Y. Fukami;H.T. Suchiya
  6. J Inst. Electron. Commun Eng Japan v.57-C no.8 BaTiO₃ Ceramic Semiconductors by Liquid Phase Sintering T. Fukami
  7. J. Am. Ceram. Soc. v.59 no.11-12 Sintering Process of Semiconductive BaTiO₃ Ceramics Y. Yoneda;H. Kato;H. Sasaki
  8. Ceram. Bull. v.62 no.2 Electrical Properties of Semiconducting BaTiO₃ by Liquid-Phase Sintering W.Y. Howng;C. McCutcheon
  9. Naturwiss v.49 O. Eberspach
  10. Phys. Status Solidi v.35 Conducting and Insulating Incorporation of Antimony into BaTiO₃Lattice H. Schmelz
  11. Phys. Status Solidi v.31 Incorporation of Antimony into Barium Titanate Lattice H. Schmelz
  12. Phys. Status Soli (a) v.47 The Influence of Kinetic Process on the Electrical Conductivity Donor-doped BaTiO₃Ceramics R. Wernicke
  13. J. Am. Ceram. Soc. v.38 no.3 Phase Equilibria in the System BaO-TiO₂ D.E. Rase;R. Roy
  14. J. Am. Ceram. Soc. v.57 H.M. O'Bryan,Jr;J. Thomson,Jr
  15. J. Am. Ceram. Soc. v.38 no.11 BTiO₃-SiO₂ Phase Diagram D.E. Rase;R. Rov
  16. J. Res. N.B.S.-A v.74.A no.2 Synthesis and Growth of Fresnoite $(Ba_2TiSi_2O_8)$ from a TiO₂Flux and its Relation to the System BaTiO₃-SiO₂ C.R. Robbins
  17. Glastechn, ber. v.49 no.9 On the System BaO-TiO₂-SiO₂ N. Koppen;A. Dietzel
  18. Yogyo-Kyokai-Shi v.93 no.5 Sintering of Semiconducting BaTiO₃ Doped with Si₃N₄ N. Yamamoto;O. Kamigaito
  19. J. Kor. Ceram. Soc. v.31 no.2 Effect of Sb₂O₃ Addition on the Microstructure and PTCR Characteristic in BaTiO₃Ceramics J.S. Kim;B.H. Lee;K.H. Lee
  20. Philips Res Rev v.31 no.6 Electrical Conductive at High Temperature of Doner-doped Barium Titanate Ceramics J. Daneil;K.H. Hardtl
  21. Philips Res Rev v.38 no.3 The PTC Effect of Barium Titanate J. Daneil;K.H. Hardtl;R. Wernicke