Journal of the Korean Ceramic Society (한국세라믹학회지)

The Korean Ceramic Society (한국세라믹학회)
권호 표지

Rapid Debinding of Low Pressure Injection Molded Parts by Wicking and Subsequent Thermal Pyrolysis

위킹 및 후속 열분해 탈지에 의한 저압 사출제의 가속탈지

  • 최인묵 (한양대학교 무기재료공학과) ;
  • 김민기 (서울대학교 무기재료공학과) ;
  • 김상우 (한국과학기술연구원 세라믹공정연구센터) ;
  • 이해원 (한국과학기술연구원 세라믹공정연구센터) ;
  • 송휴섭 (한국과학기술연구원 세라믹공정연구센) ;
  • 최성철 (한양대학교 무기재료공학과)
  • Published : 1998.06.01
Download PDF
⟨ Previous Next ⟩

Abstract

When the low pressure injection molded parts are debinded by wicking and subsequent thermal pyrolysis the optimum transition point from wicking to thermal pyrolysis is just after the completion of the constant wicking rate period. Even when the partially debinded parts were heated at 5$^{\circ}C$/min after reaching the 1st falling rate period the debinding defects such as distortion and cracks were not found.

Keywords

References

  1. Am. Ceram. Soc. Bull v.70 no.5 Fabrication of Engineering Ceramics by Injection Molding M.J. Edirishinghe
  2. Int J. High Tech. Ceram. v.2 no.4 Fabrication of Engineering Ceramics by Injection Molding. Ⅱ. Techniques M.J. Edirishinghe;J.R.G. Evans
  3. Am. Ceram. Soc. Bull. v.73 Low Pressure Injection Molding J.A. Mangels
  4. Powder Met. Int. v.21 Injection Molded Ceramic Rotors-Comparison of SiC and Si₃N₄ K. Hunold;J. Greim;A. Lipp
  5. Advances in Ceramics v.9 Ceramic Comonents by Injection Molding J.A. Mangels;W Trela;J. Mangels(ed.)
  6. Mat. Sci. Eng. v.A109 Systematic Development of the Ceramic Injection Molding Process M.J Edirisinghe;J.R.G. Evans
  7. Am. Ceram. Soc. Bull. v.70 no.8 Key Issues in Powder Injection Molding R.M. German;K.F. Hans;S.T.P. Lin
  8. Interceram. v.38 no.2 Injection Molding Machine for High-Performance Ceramics M. Inoue;Y. Kihara;Y. Arakida
  9. Br. Ceram. Trans. J. v.87 The Influence of Mixing Route on the Properties of Ceramic Injection Moulding Blends K.N. Hunt;J.R.G. Evans
  10. J. Mater. Sci. v.22 Properties of Ceramic Injection Moulding Formulations. Part Ⅰ: Melt Rheology M.J. Edirisinghe;J.R.G. Evans
  11. Ceram. Int. v.16 A Method for Selecting Organic Materials for Ceramic Injection Moulding S.J. Stedman;J.R.G. Evans;J. Woodthorpe
  12. Ceram. Int. v.17 The Effect of Processing Additives on the Properties of a Ceramic-Polymer Formulation M.J. Edirisinghe
  13. J. Mater. Sci. v.26 Fracture Strength of Low-Pressure Injection-Molded Reaction Bonded Silicon Nitride S.J. Kwak;E. Krug;S.C. Danforth
  14. Ceram. Int. v.22 Pore Structure Evolution During Solvent Extraction and Wicking S.W. Kim;H.W. Lee;H. Song;B.H. Kim
  15. Int. J. Powder Mat. v.23 Theory of Thermal Debinding R.M. German
  16. Ceram. Int. v.17 Removal of Organic Vehicle from Moulded Ceramic Bodies by Capillary Action J.K. Wright;J.R.G. Evans
  17. Ceramic Processing and Sintering M.N. Rahaman