Study on the Profile of Nut Bearing Surface and the Torque Coefficient of a High Strength Bolt Set

고장력 볼트세트의 자리면형상과 토크계수에 관한 연구

  • 이백준 (아주대학교 대학원) ;
  • 손승요 (아주대학교 기계 및 산업공학부)
  • Received : 2000.01.29
  • Published : 2000.04.27

Abstract

Depending upon the combination of tolerances specified in the standards on bolt, nut and washer for high tension bolt sets, there arises center-to-center deviation between bolt and washer. This deviation nay cause loss of effective contact area between nut- and washer-faces, which leads to some dispersion of the torque coefficient K. By adapting circular arc surface instead of flat surface for the nut, it is shown through numerical analyses that the dispersion of the torque coefficient can be minimized. In this way, optimum radius of curvature of the nut bearing surface is proposed.

마찰접합용 고장력 볼트 셋트의 관련 규격에서 허용하는 치수공차 범위 내에서 너트 구멍의 편심과 와셔 구멍 지름의 공차는 체결 시 편심에 의한 접촉면적의 결손을 초래하고 체결력의 산포를 유발하는 요인이 된다. 편평한 너트 자리면과 와셔의 접촉시 분포되는 압력의 비선형성을 고려하여 편평한 자리면 형상을 원호곡면으로 바꾸면 초기 선 접촉은 체결이 진행됨에 따라 면 접촉으로 발전한다. 원호 접촉면은 편심에 의한 접촉면적의 결손을 감소시켜 접촉상태가 양호해지므로 자리면 마찰토크(체결력) 안정화에 기여하게 된다. 유한요소법으로 너트와 와셔 접촉면의 압력을 구하고 나사면과 자리면의 마찰계수는 토크계수 A, B급이 포함되도록 조합하고 최대편심 시 토크계수를 계산하였다. 토크계수의 분포로부터 원호자리면의 적정 곡률반지름이 결정된다.

Keywords

References

  1. 나사기술총람 손승요;신금하;김영조
  2. 한국강구조학회 논문집 v.6 no.3 TS볼트체결에서 체결력, 토크계수 및 품질관리에 관한 연구 손승요(등)
  3. KS B 1010-1981, 마찰접합용 고장력 6각 볼트.6각 너트.평와셔 세트
  4. A Study on the Development of Super High Strength Bolts Kim, Jin-Ho
  5. 대한 기계학회 논문집 v.13 유한요소 접촉해석법에 의한 나사체결부 설계개선에 관한 연구 이병채;김영곤
  6. ねじ締結における座面壓につぃて 賀勢晋司
  7. ねじ締結?設計のポイント 吉本勇
  8. HyperMesh User's Manual
  9. ABAQUS/Standard User's Manual Hibbitt;Karlsson & Sorensen, Inc