한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

가상 공작기계의 연구 개발 - Part 2 (동절삭력 모델, 열적 거동 모델, 이송계 모델 및 통합 소프트웨어)

Development of a Virtual Machine Tool - Part 2 (Dynamic Cutting Force Model, Thermal Behavior Model, Feed Drive Model and Comprehensive Software Environment)

  • 발행 : 2001.11.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In Part 2, dynamic cutting force model, thermal behavior model, and feed drive model are presented for development of a virtual machine tool. Some relevant results with brief descriptions for each model are presented to verify the proposed models. Experimental results for each model agreed well with the estimated ones. The developed models in this two-part paper are partially integrated as a comprehensive software environment.

키워드

참고문헌

  1. Ehmann, K. F., DeVor, R. E., De Meter, E. C., Dornfeld, D., Kapoor, S. G., Ni, J., Rajukar, K., Shin, Y., and Sutherland, J., 'A Framework For a Virtual Machine Tool(VMT),' Trans. of NAMRI/SME, Vol. XXI, pp. 143-148, 1998
  2. 윤원수, 고정훈, 조동우, '가상 공작기계의 연구 개발-Part 1,' 한국정밀공학회지, Vol. 18, No. 11, pp. 74-79, 2001
  3. Takata, S., Tsai, M. D., and Sata, T., 'A Cutting Simulation System for Machinability Evaluation using a Workpiece Model,' Annals of the CIRP, Vol. 38(1), pp. 417-420, 1989
  4. 황철현, 조동우, '엔드밀링에서의 동절삭력 모델을 이용한 채터예측,' 한국정밀공학회지, Vol. 16, No. 2, pp. 104-115, 1999
  5. Tlusty, J., Smith, S, and Zamudio, C., 'New NC Routines for Quality in Milling,' Annals of the CIRP, Vol.40/1, pp. 517-521, 1990
  6. Kang, S.J., Cho, D.W., and Chun, C.K., 'Evaluation Stability of a Transient Cut during Endmilling using the Dynamic Cutting Force Model,' Int. Jour. of the KSPE, Vol. 1, No. 2, pp. 67-75, 2000
  7. Yang,S., Yuan, J., and Ni, J., 'The Improvement of Thermal Error Modeling and Compensation on Machine Tools by CMAC Neural Network,' International Journal of Machine Tools and Manufacture, Vol. 36, No. 4, pp. 527-537, 1996 https://doi.org/10.1016/0890-6955(95)00040-2
  8. 이강인, 조동우, '수정된 신경망을 이용한 공작 기계의 열변형 오차 예측모델 개발,' 한국 정밀공학회 추계학술대회, 서울, 고려대학교, , pp. 226-230, 1999
  9. Ahn, K.G. and Cho, D. W., 'In-process Modeling and Estimation of Thermally Induced Errors of a Machine Tool During Cutting,' The International Journal of Advanced Manufacturing Technolo, Vol.15, pp.299-304, 1999 https://doi.org/10.1007/s001700050070
  10. Yun, S. H., 'Adaptive Control of Milling Force by Indirect Measurement of Cutting Forces,' M.S Thesis, POSTECH, 1999