DOI QR코드

DOI QR Code

F. E.-assisted design of the eaves bracket of a cold-formed steel portal frame

  • Lim, J.B.P. (The Steel Construction Institute) ;
  • Nethercot, D.A. (I.C.S.T.M.)
  • 투고 : 2002.07.01
  • 심사 : 2002.09.01
  • 발행 : 2002.12.25

초록

Non-linear large-displacement elasto-plastic finite element analyses are used to propose design recommendations for the eaves bracket of a cold-formed steel portal frame. Owing to the thinness of the sheet steel used for the brackets, such a structural design problem is not trivial as the brackets need to be designed against failure through buckling; without availability of the finite element method, expensive laboratory testing would therefore be required. In this paper, the finite element method is firstly used to predict the plastic moment capacity of the eaves bracket. Parametric studies are then used to propose design recommendations for the eaves bracket against two potential buckling modes of failure: (1) buckling of the stiffened free-edge into one-half sine wave, (2) local plate buckling of the exposed triangular bracket area.The results of full-scale laboratory tests on selected geometries of eaves bracket demonstrate that the proposed design recommendations are conservative. The use of the finite element method in this way exploits modern computational techniques for an otherwise difficult structural design problem.

키워드

참고문헌

  1. AlSl(1996), Specification for The Design of Cold-Formed Steel Structural Members. American lron and Steel lnstitute, Washington.
  2. Baigent, A.H. and Hancock, G.J.(1982), "The behaviour of portal frames composed of cold-formed members", Thin -Walled Structures - Recent technical advances and trends in design, research and construction , Elsevier Applied Science, Oxford, p209.
  3. BS5950: Part 5 (1992), Code of Practice for Design of Cold-Formed Sections , British Standards lnstitution, London.
  4. Chung, K.F. and lp, K.H.(2000), "Finite element modeling of bolted connections between cold-formed steelstrips and hot-rolled steel plates under static shear loading", Engng Struct, 22, 1271. https://doi.org/10.1016/S0141-0296(99)00082-6
  5. Chung, K.F. and Lau, L.(1999), "Experimental investigation on bolted moment connections among cold-formedsteel members", Engng Struct, 21, 898. https://doi.org/10.1016/S0141-0296(98)00043-1
  6. Davies, J.M. and Brown, B.A.(1996), Plastic Design to BS 5950, Ascot, The Steel Construction lnstitute, Blackwell Scientific Publishers.
  7. Eurocode 3 (1996), Design of Steel Structures: Part 1.3 - General rules and rules for buildings, Committee European de Normalisation, Brussels.
  8. Hancock, G.J.(1998), Design of Cold-Formed Steel Structures, Australian lnstitute of Steel Construction, 3rd ed..
  9. Hibbit, Karlsson and Sorensen, lnc.(1995a), ABAQUS Theory Manual, Hibbitt, Karlsson and Sorensen, lnc.
  10. Hibbit, Karlsson and Sorensen, lnc.(1995b), Element selection in ABAQUS/Standard, ABAQUS Lecture Notes Series, Hibbitt, Karlsson and Sorensen, lnc.
  11. Horne, M.R. and Morris, L.J. (1981), Plastic Design of Low- Rise Frames, Constrado monograph, Granada Publishing.
  12. Kirk, P.(1986), "Design of a cold-formed section portal frame building system", Proc 8th lnternational Speciality Conference on Cold-formed Steel Structures, St. Louis, University of Missouri-Rolla, 1986, p295.
  13. Kulak, G.C, Fisher, J.W. and Struik, J.H.A.(1987), Guide to Design Criteriafor Bolted and Riveted Joints, 2nd ed., John Wiley and Sons, New York.
  14. Lim, J.B.P.(2001), "Joint effects in cold-formed steel portal frames", University of Nottingham, PhD thesis.
  15. Lim, J.B.P. and Nethercot, D.A.(2002a), "Design and development of a general cold-formed steel portal framingsystem", The Structural Engineer, 80(21),2002, 31.
  16. Lim, J.B.P. and Nethercot, D.A.(2002b), "Serviceability design of a cold-formed steel portal frame having semirigid joints", to be submitted.
  17. Lim, J.B.P. and Nethercot, D.A. (2002c), "Stiffness prediction for bolted moment-connections between cold-formed steel members", to be submitted.
  18. Lim, J.B.P. and Nethercot, D.A. (2002d), "Ultimate strength of bolted moment-connections between cold-formedsteel members", to be submitted.
  19. Owens, G.W. and Cheal, B.D.(1989), Structural Steelwork Connections, Butterworth, London.
  20. Rhodes, J. (1991): Design of Cold-Formed Steel Members, Elsevier Applied Science, Oxford.
  21. Schafer, B.W., Grigoriu, M., Pekoz, T.(1996), "A probabilistic examination of the ultimate strength of cold-formed steel elements", Proc 13th lnternational Speciality Conference on Cold-Formed Steel Structures, St Louis, University of Missouri-Rolla.
  22. Schafer, B.W., Pekoz, T. (1998), "Computation modeling ofcold-for med steel: characterizing geometric imperfections and residual stresses",Thin-Walled Structures, 47, 193.
  23. SCI/BCSA(1995a), Joints in Steel Construction: Simple Connections, SCI/BCSA.
  24. SCI/BCSA(1995b), Joints in Steel Construction: Moment Connections, SCI/BCSA.
  25. Stanway, G.S., Chapman, J.C. and Dowling, P.J.(1993), "Behaviour of a web plate in shear with an intermediate stiffener", Proc. lnstn. Civ. Engrs Structs Bldgs, 99, 327. https://doi.org/10.1680/istbu.1993.24354
  26. Wang, C.M. and Liew, K.M. (1994), "Buckling of triangular plates under uniform compression", Engng Struct, 16, 43. https://doi.org/10.1016/0141-0296(94)90103-1
  27. Woolcock, S.T., Kitipornchai, S., Bradford, M. A. (1999), Limit State Design of Portal Frame Buildings, 3rd ed., Australian Institute of Steel Construction, Sydney.

피인용 문헌

  1. Optimum Joint Detail for a General Cold-Formed Steel Portal Frame vol.15, pp.9, 2012, https://doi.org/10.1260/1369-4332.15.9.1623
  2. Research on cold-formed steel connections: A state-of-the-art review vol.20, pp.1, 2016, https://doi.org/10.12989/scs.2016.20.1.021
  3. Ultimate strength of bolted moment-connections between cold-formed steel members vol.41, pp.11, 2003, https://doi.org/10.1016/S0263-8231(03)00045-4
  4. Experimental and numerical study on a full scale apex connection of cold-formed steel portal frames vol.94, 2015, https://doi.org/10.1016/j.tws.2015.04.004
  5. Finite Element Idealization of a Cold-Formed Steel Portal Frame vol.130, pp.1, 2004, https://doi.org/10.1061/(ASCE)0733-9445(2004)130:1(78)
  6. Effects of elevated temperatures on bolted moment-connections between cold-formed steel members vol.29, pp.10, 2007, https://doi.org/10.1016/j.engstruct.2006.11.027
  7. Design of Top-hat Purlins for Cold-formed Steel Portal Frames vol.7, 2016, https://doi.org/10.1016/j.istruc.2016.06.006