Transactions of the Korean Society of Mechanical Engineers A (대한기계학회논문집A)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

Friction Characteristics of Piston Assembly (II) -Experiment-

피스톤계 마찰 특성 (II) -실험적 연구-

  • 조명래 (현대자동차 파워트레인연구소) ;
  • 하경표 (현대자동차 파워트레인연구소) ;
  • 김중수 (현대자동차 파워트레인연구소) ;
  • 오대윤 (현대자동차 파워트레인연구소) ;
  • 한동철 (서울대학교 기계항공공학부)
  • Published : 2003.01.01
Download PDF
⟨ Previous Next ⟩

Abstract

The aim of this paper is to investigate the friction characteristics of piston assembly, which composed of ring pack and piston skirt. The friction force of piston assembly was measured by using the movable liner in the single cylinder engine, and the various parameters were tested. The friction force was suddenly increased at the expansion stroke due to higher cylinder pressure. The viscous friction was dominant at the mid stroke, but the boundary friction was dominant at the top and bottom dead centers. Through the experiment, we could validate previous theoretical study, and confirm that th e radial clearance and ring tension were very effective to reduce friction loss of piston assembly.

Keywords

References

  1. Kim, W. Q., Seo, S. H., Kang, K. P. and Oh, D. Y., 2001, 'Development of Low Viscosity Engine Oil,' 2001 Research Paper Conference in Hyundai Motor
  2. Furuhama, S. and Takiguchi, M., 1979, 'Measurement of Piston Frictional force in Actual Operating Diesel Engine,' SAE paper, No. 790855
  3. Wakuri, Y., Kitahara, T., Hamatake, T., Soejima, M. and Oono, O., 1996, 'Characteristics of Piston Ring Friction (Influences of Piston Ring Specifications),' J. of JSME, 62(599), pp. 2811-2817 https://doi.org/10.1299/kikaic.62.2811
  4. Halsband, M., 1995, 'MEASUREMENT OF PISTON ASSEMBLY FRICTION FORCE IN SMALL HIGH SPEED GASOLINE ENGINES,' Proc. Int. Trib. Conf., Yokohama, pp. 1447-1451
  5. Koch, F., Geiger, U. and Hermsen, F.-G., 1996, 'PIFFO - Piston Friction Force Measurements During Engine Operation,' SAE paper, No. 960306
  6. Yoon, J. Y. and Kim S. S., 1994, 'Development of Piston-Ring Assembly Friction Force Measuring System,' J. of KSAE. Vol. 2, No.3, pp.94-104
  7. Yoon, J. Y. and Kim S. S., 1994, 'Friction Characteristics of the Piston-Ring Assembly Varying Engine Operation Conditions,' Trans. KSME Journal, Vol. 18, No.6, pp.1510-1519
  8. Cho, S. W., Choi, S. M. and Bae, C. S., 2000, 'The Frictional Modes of Piston Rings for an SI Engine,' J. of KSAE, Vol. 8, No.5, pp.114-120
  9. Lee, J. S. and Han, D. C., 1999, 'An Experimental Study on Frictional Characteristics of the Piston Ring,' J. of KSAE, Vol. 7, No. 6, pp.115-122
  10. Cho, M. R., Choi, J. K. and Han, D. C., 2001, 'Calculation of Mixed Lubrication at Piston Ring and Cylinder Liner Interface,' KSME Int. Journal, Vol. 15, No.7, pp. 859-865