한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

  • 제20권8호
  • /
  • Pages.101-107
  • /
  • 2003
  • /
  • 1225-9071(pISSN)
  • /
  • 2287-8769(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

3 분력 힘 센서를 이용한 CMM 용 접촉식 프로브의 개발에 관한 연구

A Study of Development for Contact CMM Probe using Three-Component Force Sensor

  • 송광석 (한양대 대학원 정밀기계공학과) ;
  • 권기환 (한양대 대학원 정밀기계공학과) ;
  • 박재준 (한양대 대학원 정밀기계공학과) ;
  • 조남규 (한양대 기계공학과)
  • 발행 : 2003.08.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

A new mechanical probe for 3-D feature measurement on coordinate measuring machines (CMMs) is presented. The probe is composed of the contact stylus and the three-component force sensor. With the stylus mounted on the force sensor, the probe can not only measure 3-D features, but also detect contact force acting on the stylus tip. Furthermore, the probing direction and the actual contact position can be determined by the relationship among three components of contact force to be detected. In this paper, transformation matrix representing the relationship between the external force acting on the stylus tip and the output voltages of measurement gauges is derived and calibrated. The prototype of probe is developed and its availability is investigated through the experimental setup for calibration test of the probe. A series of experimental results show that the proposed probe can be an effective means of improving the accuracy of touch probing on CMM.

키워드

참고문헌

  1. W. Tyler Estler, Phillips, S. D., Borchardt, B., Hopp, T., Witzgall, C., Levenson, M., Eberhardt, K., McClain, M., Shen, Y. and Zhang, X., 'Error Compensation for CMM Touch Trigger Probes,' Precision Engineering, Vol. 19, pp. 85-97, 1996 https://doi.org/10.1016/S0141-6359(96)00040-2
  2. W. Tyler Estler, Phillips, S. D., Borchardt, B., Hopp, T., Levenson, M., Eberhardt, K., McClain, M., Shen Y. and Zhang, X., 'Practical Aspects of Touch-Trigger Probe Error Compensation,' Precision Engineering, Vol. 21, Issue 1, pp. 1-17, 1997 https://doi.org/10.1016/S0141-6359(97)00062-7
  3. J. R. Rene Mayer, Abdeljabbar Ghazzar, Olivier Rossy, '3D Characterization, Modeling and Compensation of the Pre-travel of a Kinematic Touch Trigger Probe,' Measurement, Vol. 19, No.2, pp. 8394,1996 https://doi.org/10.1016/S0263-2241(96)00068-1
  4. Kim, S. H., Lee, S. J. and Kim, O. H., 'The Analysis of Measuring Error in OMM System,' J. of the KSPE, Vol. 15 No. 5, pp. 34-42,1998
  5. Lee, Se-Hee, Cho, Myeong-Woo and Seo, Tae-Il, 'Measurement Error Modeling for On-Machine Measurement of Sculptured Surfaces,' Int. J. of the KSPE, Vol. 2, No.2, pp. 73-80,2001
  6. Xiong, Z. H., Li, Z. X., 'Error compensation of workpiece localization,' IEEE Inter. Conf. on Robotics and Automation, pp. 2249-2254, 2001 https://doi.org/10.1109/ROBOT.2001.932957
  7. Shuh-Ren Liang and Alan C. Lin, 'Probe-Radius Compensation for 3D Data Points in Reverse Engineering,' Computers in Industry, Vol. 48, Issue 3, pp. 241-251, 2002 https://doi.org/10.1016/S0166-3615(02)00038-6
  8. Steven D. Bittle and Thomas R. Kurfess, 'An Active Piezoelectric Probe for Precision Measurement on a CMM,' Mechatronics, Vol. 7, No.4, pp. 337-354, 1997 https://doi.org/10.1016/S0957-4158(97)00005-6
  9. Wim P. van Vliet, Peter H. J. Schellekens, 'Development of a Fast Mechanical Probe for Coordinate Measuring Machines,' Precision Engineering, Vol. 22, pp. 141-152, 1998 https://doi.org/10.1016/S0141-6359(98)00008-7
  10. Joao Bosco de Aquino Silva, M. Burdekin, 'A Modular Space Frame for Assessing the Performance of Coordinate Measuring Machines (CMMs),' Precision Engineering, Vol. 26, pp. 37-48, 2002 https://doi.org/10.1016/S0141-6359(01)00096-4