Permeability Measurement of a Circular Braided Preform for Resin Transfer Molding

  • Cho, Yun Kyoung (School of Materials Science and Engineering, Seoul National University) ;
  • Song, Young Seok (School of Materials Science and Engineering, Seoul National University) ;
  • Kang, Tae Jin (School of Materials Science and Engineering, Seoul National University) ;
  • Chung, Kwansoo (School of Materials Science and Engineering, Seoul National University) ;
  • Youn, Jae Ryoun (School of Materials Science and Engineering, Seoul National University)
  • 발행 : 2003.09.01

초록

Permeability of the preform is one of key factors in design of RTM (Resin Transfer Molding) mold, determination of processing conditions, and modeling of flow in the mold. According to previous studies, permeability measured in the unsaturated fiber mats are higher than that in the saturated fiber mats by about 20% because of the capillary pressure. In this study, permeabilities of several fiber preforms are measured for both saturated and unsaturated flows. A saturated experiment of radial flow has been adopted to measure the permeability of anisotropic fiber preforms with high fiber content, i.e., circular braided preforms. In this method, four pressure transducers are used to measure the pressure distribution. Permeabilities in different directions are determined and the experimental results show a good agreement with the theory. Since permeability is affected by the capillary effect, permeability should be measured in the unsaturated condition for the textile composites to be manufactured under lower pressure as in the Vacuum Assisted Resin Transfer Molding (VARTM).

키워드

참고문헌

  1. S. G. Advani, M. V. Bruschke, and R. S. Pamas, 'Flow and Rheology in Polymer Composites Manufacturing', Elsevier, Amsterdam, 1994
  2. R. A. Greenkom, 'Flow Phenomena in Porous Media', Marcel Dekker, New York, 1983
  3. K. L. Ahn and J. C. Seferis, Polym. Compos., 12, 146 (1991) https://doi.org/10.1002/pc.750120303
  4. W.B. Young, J. Compos. Mater., 30, 1191 (1996) https://doi.org/10.1177/002199839603001102
  5. S. Amico and C. Lekakou, Compos. Sci. Technol., 61, 1945-1959 (2001) https://doi.org/10.1016/S0266-3538(01)00104-X
  6. K. L. Adams and L. Rebenfeld, Polym. Compos., 12, 179-185 (1991) https://doi.org/10.1002/pc.750120307
  7. K. L. Adams, W. B. Russel, and L. Rebenfeld, Int. J. Mul-tiphase Flow, 14, 203-215 (1988) https://doi.org/10.1016/0301-9322(88)90006-7
  8. K. L. Adams and L. Rebenfeld, Polym. Compos., 12, 186 (1991) https://doi.org/10.1002/pc.750120308
  9. K. K. Han, C. W. Lee, and B. P. Rice, Compos. Sci. Tech-nol.,60, 2435 (2000) https://doi.org/10.1016/S0266-3538(00)00037-3
  10. R. S. Pamas, K. M. Flynn, and M. E. Dal-Favero, Polym. Compos., 18, 623-633 (1997) https://doi.org/10.1002/pc.10313
  11. Y. Luo, I. Verpoest, K. Hoes, M. Vanheule, H. Sol, and A. Cardon, Compos. Part A- Appl. Sci., 32, 1497-1504 (2001) https://doi.org/10.1016/S1359-835X(01)00049-5
  12. Y. H. Lai, B. Khomarni, and J. L. Kardos, Polym. Compos., 18, 368-377 (1997) https://doi.org/10.1002/pc.10288
  13. R. Gauvin, F. Trochu, Y. Lemenn, and L. Diallo, Polym. Compos., 17, 34-42 (1996) https://doi.org/10.1002/pc.10588
  14. H. Golestanian and A. S. El-Gizawy, Polym. Compos., 19, 395-407 (1998) https://doi.org/10.1002/pc.10113
  15. A. W. Chan and S. T. Hwang, Polym. Eng. Sci., 31, 1233 (1991) https://doi.org/10.1002/pen.760311613
  16. R. S. Pamas and A. J. Salem, Polym. Compos., 14, 383-394 (1993) https://doi.org/10.1002/pc.750140504
  17. T. J. Wang, C. H. Wu, and L. J. Lee, Polym. Compos., 15, 278 (1994) https://doi.org/10.1002/pc.750150406
  18. J. R. Weitzenbock, R. A. Shenoi, and P. A. Wilson, Com-pos. Part A- Appl. Sci., 30, 781-796 (1999) https://doi.org/10.1016/S1359-835X(98)00183-3
  19. Z. X. Tang and R. Postle, Compos. Struct., 49, 451 (2000) https://doi.org/10.1016/S0263-8223(00)00082-9
  20. A. C. Long, Compos. Part A- Appl. Sci., 32, 941-953 (2001) https://doi.org/10.1016/S1359-835X(00)00153-6
  21. D. G. Seong, K. Chung, T. J. Kang, and J. R. Youn, Polym. Polym. Compos., 10, 493 (2002)
  22. Y. S. Song, K. Chung, T. J. Kang, and J. R. Youn, Polym. Polym. Compos., 11, in press (2003)