DOI QR코드

DOI QR Code

Deformation and Fracture Behavior of Structural Bulk Amorphous Metal under Quasi-Static Compressive Loading

준정적 압축하에서 구조용 벌크 아몰퍼스 금속의 변형 및 파괴거동

  • 신형섭 (안동대학교 기계공학부) ;
  • 고동균 (안동대학교 대학원 기계공학과) ;
  • 오상엽 (가톨릭상지대학 자동차계열)
  • Published : 2003.10.01

Abstract

The deformation and fracture behaviors of a bulk amorphous metal, Zr-based one (Zr$\_$41.2/Ti$\_$13.8/Cu$\_$12.5/Ni$\_$10/Be$\_$22.5/: Vitreloy), were investigated over a strain rate range (7x10$\^$-4/~4 s$\^$-1/). The uniaxial compression test and the indentation test using 3mm-diameter WC balls were carried out under quasi-static loading conditions. As a result, at the uniaxial compressive state, the fracture stress of the material was very high (~1,700MPa) and the elastic strain limit was about 2%. The fracture strength showed a strain rate independent behavior up to 4 s$\^$-1/. Using indentation tests, the plastic deformation behavior of the Zr-based BAM up to a large strain value of 15% could be achieved, even though it was the deformation under locally constrained condition. The Meyer hardness of the Zr-based BAM measured by static indentation tests was about 5 GPa and it revealed negligible strain hardening behavior. At indented sites, the plastic indentation occurred forming a crater and well-developed multiple shear bands were generated around it along the direction of 45 degree when the indentation load exceeded 7kN. With increasing indentation load, shear bands became dense. The fracture surface of the specimen after uniaxial compressive tests showed vein-like pattern, typical morphology of many BAMs.

Keywords

References

  1. Inoue, A., 2000 'Stabilization of Metallic Supercooled Liquid and Bulk Amorphous Alloys,' Acta. Mater., Vol. 48, pp. 279-306 https://doi.org/10.1016/S1359-6454(99)00300-6
  2. Johnson, W. L., 1999 'Bulk Glass-Forming Metallic Alloys: Science and Technology,' MRS Bull. Vol. 24, pp. 42-56 https://doi.org/10.1557/S0883769400053252
  3. Bruck, H. A., Christman, T., Rosakis, A. J. and Johnson W. J., 1994, 'Quasi-static Constitutive Behavior of Zr-based Bulk Amorphous Alloys,' Scripta Metal. Mater. Vol. 30, pp. 429-434 https://doi.org/10.1016/0956-716X(94)90598-3
  4. Lowhaphandu, P., Ludrosky, L. A., Montgomery, S. L. and Lewandowski, J. J., 2000, 'Deformation and Fracture Toughness of A Bulk Amorphous Zr-Ti-Ni-Cu-Be Alloy,' Intermetallics, Vol. 8, pp. 487-492 https://doi.org/10.1016/S0966-9795(99)00137-5
  5. Szuecs, F., Kim, C. P. and Johnson, W. L., 2001, 'Mechanical Properties of Zr-Ti-Nb-Cu-Ni-Be Ductile Phase Reinforced Bulk Metallic Glass Composite,' Acta Mater., Vol. 49, pp. 1507-1513 https://doi.org/10.1016/S1359-6454(01)00068-4
  6. Conner, R. D. Dandliker, R. B. and Johnson, W. L., 2000, 'Mechanical Properties of Tungsten and Steel Fiber Reinforced $Zr_{41.25}Ti_{13.75}Cu_{12.5}Ni_{10}Be_{22.5}$ Metallic Glass Matrix Composites,' Acta Mater., Vol. 46, pp. 6089-6102 https://doi.org/10.1016/S1359-6454(98)00275-4
  7. Wright, W. J., Schwarz, R. B. and Nix, W. D., 2001, 'Localized Heating During Serrated Plastic Flow in Bulk Metallic Glasses,' Mater. Sci. Engng., Vol. A319-321, pp. 229-232
  8. Tabor, D., 'The Hardness of Metals,' Clarendon, Oxford, 1951, pp. 115-120
  9. Mukai, T., Kawamura, Y., Inoue, A., Nieh, T. G. and Higashi, K., 2001, 'Influence of Strain Rate on the Tensile Mechanical Behavior in $Pd_{40}Ni_{40}P_{20}$ Bulk Metallic Glass,' Proc. 4th ISIE, Ed. Chiba A. et al., pp. 577-582
  10. Bruck, H. A., Rosakis, A. J. and W. J. Johnson, 1996, 'The Dynamic Compressive Behavior of Beryllium Bearing Bulk Metallic Glasses,' J. Mater. Res., Vol. 11, No. 2, pp. 503-511 https://doi.org/10.1557/JMR.1996.0060
  11. Conner, R. D., Dandliker, R. B., Scruggs, V. and Johnson, W. L., 2000, 'Dynamic Deformation Behavior of Tungsten-Fiber/Metallic-Glass Matrix Composites,' Int. J. Impact Eng., Vol. 24, pp. 435-444 https://doi.org/10.1016/S0734-743X(99)00176-1
  12. Int. J. Impact Eng. v.24 Dynamic Deformation Behavior of Trugsten-Fiber/Metallic-Glass Matrix Composites Conner,R.D.;Dandliker,R.B.;Scuggs,V.;Johnson,W.L. https://doi.org/10.1016/S0734-743X(99)00176-1