Journal of the Korean Society for Aeronautical & Space Sciences (한국항공우주학회지)

The Korean Society for Aeronautical and Space Sciences (한국항공우주학회)
권호 표지
DOI QR코드

DOI QR Code

Tensile Characteristics of A12024-T3 under Rapid Heating

급속가열환경에서 A12024-T3의 인장특성

  • Published : 2004.10.01
Download PDF
⟨ Previous Next ⟩

Abstract

The thermomechanical tensile characteristics were evaluated for A12024-T3 under heating rates from $1^{\circ}C/sec\;to\;30^{\circ}C/sec$ by using an infrared heating equipment to simulate aerodynamic heating. The rapid heating test results were compared with tensile test results after 1/2 hour exposure in terms of yield stress to investigate the influence of heating condition. A heating rate-yield temperature parameter was suggested for rapid heating based on time-temperature parameters, and master yield stress curve was obtained by using these parameter. These test results can be used for margin of safety of supersonic vehicle structures subjected to aerodynamic heating.

본 연구에서는 비행체 구조재료인 A12024-T3에 대하여 공력가열환경을 모사할 수 있는 복사가열기를 제작하였으며 $1^{\circ}C/sec{\sim}30^{\circ}C/sec$ 가열률 범위에서 열기계적 인장특성을 평가하였다. 가열환경에 따른 재료강도 평가를 위하여 급속가열 인장시험 결과와 일정 온도로 30분 노출후의 인장시험결과를 항복응력 측면에서 비교 고찰하였다. 급속가열 인장시험 결과로부터 시간-온도계수를 응용한 가열률-항복온도 계수를 도출하였으며, 항복응력을 가열률과 항복온도로 표현되는 실험적 master 수식을 제안하였다. 본 연구 결과를 통하여 획득 된 급속가열 안장시험결과들은 초음속 비행체 설계시 선정재료의 안전여유를 판단하는 기초자료로 활용될 수 있다.

Keywords

References

  1. Robert Wesley Truitt, Fundamentals of Aerodynamic Heating, The Ronald Press Company, 1960.
  2. "Metallic Materials and Elements for Aerospace Vehicle Structures", MIL-HDBK-5F, 1998.
  3. Ivo M. Kurg, "Tensile Properties of Inconel-X Sheet Under Rapid Heating and Constant Temperature Conditions", NACA TN 4065, 1957.
  4. Lipkin J., Swearengen J. C., Karnes C.H., "Mechanical properties of 6061 Al-Mg-Si Alloy after very rapid heating", J. Mech. Phys. Salids 21, pp.91-112, 1973. https://doi.org/10.1016/0022-5096(73)90032-X
  5. Zongde Liu, Shu-Lin Bai, Kun Yang, Mingbao Han, "Experimental studies on yield behavior of steel under rapid heating", Int. J. of Plasticity, 17, pp.671-701, 2001.
  6. "Standard Test Methods for Tension Testing of Metallic Materials [Metric] ,"ASTM E 8M-88, 1988.
  7. Clerk E. Beck, Handbook for Test Engineers(Radiant Heating, FDTE-TM-64-50, 1964.
  8. George E. Dieter, Mechanical Metallurgy, McGraw-Hill Company, 1986.
  9. S.S. Manson, A.M. Haferd, "A Linear Time-Temperature Relation for Extrapolation of Creep and Stress Rupture Data", NACA TN 2890, 1953.
  10. W.E. White, lain Lemay, "On-Time Temperature Parameters for Correlation of Creep-Rupture Data in Stainless Steel Weldment", J. of Engineering Materials and Technology, Vol.100, pp.319-335, 1978. https://doi.org/10.1115/1.3443497