Journal of Mechanical Science and Technology

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지

A Real-Time DSP-Based Imbalance Analysis System for Rotating Machine with Vibration Signal

  • Su Hua (Department of Electrical and Computer Engineering, Chonbuk National University) ;
  • Huang Linglong (Department of Electrical and Computer Engineering, Chonbuk National University) ;
  • Chong Kil To (Department of Electrical and Computer Engineering, Chonbuk National University)
  • Published : 2005.06.01
Download PDF
⟨ Previous Next ⟩

Abstract

This paper describes a new digital signal processor (DSP) imbalance measurement system dedicated to real-time vibration analysis on rotating machine. To accomplish real-time analysis, the vibration signals are on-line acquired and processed to analyze the mass imbalance and phase position. This is achieved through the use of FFT and Lissajous diagram. The method followed to analyze the mass imbalance with the chosen hardware and software solutions are described in detail in this paper. Several experimental tests demonstrate the efficiency and accuracy in imbalance analysis performance of the DSP system.

Keywords

References

  1. Bishop, R. E. D. and Gladwell, G. M. L., 1959, 'The Vibration and Balancing of an Unbalanced Rotor,' Journal of Mechanical Engineering Science, pp.66-77
  2. Blasco, G. R., Asher, G. M., Sumner, M. and Bradley, K. J., 1996, 'Performance of FFT-Rotor Slot Harmonic Speed Detector for Sensorless Induction Motor Drives,' IEE Proc. Electr. Power Appl., vol. 143, No.3, pp. 258-268 https://doi.org/10.1049/ip-epa:19960241
  3. Choi, M. S., 2003, 'Free Vibration Analysis of Plate Structures Using Finite Element-Transfer Stiffness Coefficient Method,' KSME International Journal, Vol. 17, No. 6, pp. 805-815
  4. Chow, T. W. S. and Hai, S., 2004, 'Induction Machine Fault Diagnostic Analysis with Wavelet Technique,' IEEE Trans. on industrial electronics, Vol. 51, No.3 https://doi.org/10.1109/TIE.2004.825325
  5. Enrich, F. F., 1987, 'Two Plane Balancing of a Rotor System Without Phase Response Measurements,' ASME Journal of Vibration, Acoustics, Stress and Reliability in Design, 109 pp. 162-167 https://doi.org/10.1115/1.3269409
  6. Hoextermann, E., 1988, 'Erfahrung Mit Schaeden in form von Anrissen und Bruecken an Dampfturbienenwellen, Radscheiben und Generatorlaufen,' VGB Technische-Wissenschaftliche Berichte Waermekraftwerke, VGW-TW 107
  7. Hong, S. H. and Seo, Y. G., 2001, 'A Study on the Synchronous Response of General Rotor-Bearing Systems due to Initial Deformation,' KSME International Journal, Vol. 15, No. 9, pp. 1226-1239
  8. Hong, S. W. and Park, J. H., 1997, 'An Efficient Method for the Unbalance Response Analysis of Rotor-Bearing Systems.' Journal of Sound and Vibration, 200(4) pp. 491-504 https://doi.org/10.1006/jsvi.1996.0773
  9. Kim, S. K. and Yoo, H. H., 2002, 'Vibration Analysis of Rotating Composite Cantilever Plates,' KSME International Journal, Vol. 16, No. 3, pp. 320-326
  10. Kim, W. K., Kim, J. T. and Kim, J. S., 2003, 'Development of a Criterion for Efficient Numerical Calculation of Structural Vibration Responses,' KSME International Journal, Vol. 17, No. 8, pp. 1148-1155
  11. Kumbla, K. K., Mohammad-R., Akbarzadeh-T. and Jamshidi, M., 1995, 'TMS320 DSP Based Neuro-Fuzzy Controller,' Systems, Man and Cybernetics, 1995. 'Intelligent Systems for the 21st Century'., IEEE International Conference on, Vol. 5, pp. 4015-4020 https://doi.org/10.1109/ICSMC.1995.538418
  12. Park, J. T. and Choi, N. S., 2004, 'Flexural Vibration Analysis of a Sandwich Beam Specimen with a Partially Inserted Viscoelastic Layer,' KSME International Journal, Vol. 18, No. 3, pp. 347-356
  13. Park, R. W., 2000, 'Estimation of a Mass Unbalance Under the Crack on the Rotating Shaft,' ICASE., Vol. 2, No.4
  14. Saito, S. and Azuma, T., 1964, 'Balancing of Flexible Rotors by the Complex Modal Method,' ASME Journal of Vibration, Series B, 86(3) pp.273-279
  15. Shimada, K. and Miwa, S., 1980, 'Balancing of a Flexible Rotor,' Bulletin of the JSME, 23(180) pp.938-944 https://doi.org/10.1299/jsme1958.23.938
  16. Shin, G. O. Y. and Lee, A., 1997, 'Identification of the Unbalance Distribution in Flexible Rotors,' Int. J. Mech. Sci., Vol. 39. No. 7., pp.841-857 https://doi.org/10.1016/S0020-7403(96)00078-1
  17. Su, Hua and Chong, K. T., 2004, 'An Efficient Method for the Mass Unbalance Analysis of a Rotor System Using FFT and Lissajous Diagram,' in 2004 International Conference of Control, Automation and Systems, Bangkok, Thailand
  18. Tahk, K. M. and Shin, K. H., 2002, 'A Study on the Fault Diagnosis of Roller-Shape Using Frequency Analysis of Tension Signals and Artificial Neural Networks Based Approach in a Web Transport System,' KSME International Journal, Vol. 16, No. 12, pp. 1604-1612
  19. Wylie, C. R. and Barrett, L. C., 1982, Advanced Engineering Mathematics, McGraw-Hill
  20. Xu, H. S., Toliyat, H. A. and Petersen, L. J., 2002, 'Five-Phase Induction Motor Drives with DSP-Based Control System,' Power Electronics, IEEE Transactions on, Vol. 17, Issue. 4, pp. 524-533 https://doi.org/10.1109/TPEL.2002.800983
  21. Zhou, J. S., Liu, Z. Y. and Pei, R., 2001, 'A New Nonlinear Model Predictive Control Scheme for Discrete-Time System Based on Sliding Mode Control,' American Control Conference, 2001. Proceedings of the 2001, Vol. 4, pp. 3079-3084 https://doi.org/10.1109/ACC.2001.946390
  22. Texas Instruments TMS320C3X User's Guide 2001