Efficiency of an SCM415 Alloy Surface Layer Implanted with Nitrogen Ions by Plasma Source Ion Implantation

  • Lyu, Sung-Ki (School of Mechanical & Aerospace Eng., ReCAPT, Gyeongsang National University) ;
  • He, Hui-Bo (Graduate School, Gyeongsang National University) ;
  • Lu, Long (Huaihai Institute of Technology) ;
  • Youn, Il-Joong (School of Mechanical & Aerospace Eng., Gyeongsang National University)
  • 발행 : 2006.10.01

초록

SCM415 alloy was implanted with nitrogen ions using plasma source ion implantation (PSII), at a dose range of $1{\times}10^{17}\;to\;6{\times}10^{17}\;N^+cm^{-2}$ Auger electron spectrometry (AES) was used to investigate the depth profile of the implanted layer. Friction and wear tests were carried out on a block-on-ring wear tester. Scanning electron microscopy (SEM) was used to observe the micro-morphology of the worn surface. The results revealed that after being implanted with nitrogen ions, the frictional coefficient of the surface layer decreased, and the wear resistance increased with the nitrogen dose. The tribological mechanism was mainly adhesive, and the adhesive wear tended to become weaker oxidative wear with the increase in the nitrogen dose. The effects were mainly attributed to the formation of a hard nitride precipitate and a supersaturated solid solution of nitrogen in the surface layer.

키워드

참고문헌

  1. Byelia, A. V., 'High current density ion implantation and its application to improve the wear resistance of ferrous materials,' Wear 203-204, pp. 596-607, 1997 https://doi.org/10.1016/S0043-1648(96)07420-0
  2. Lu, L. and Lyu , S. K., 'A study on the friction and wear characteristics of c-n coated spur gear,' The Korean Society of Tribologist & Lubrication Engineering, Vol. 20, No. 5, pp. 272-277, 2004
  3. Lyu , S. K. and Lu, L., 'A study on the friction and wear characteristics of C-N coated SCM415 steel,' Journal of the KOSOS, Vol. 20, No. 1, pp. 18-23, 2005
  4. Conrad, J. R., Radtke, J. L., Dodd, R. A., Worzala, F. J. and Tran, N. C., 'Appl. Phys. 62,' p. 4591, 1987 https://doi.org/10.1063/1.339055
  5. Collins, G. A., Hutchings, R. and Tendys, J., 'Advanced surface treatments by plasma ion implantation,' Surf. Coat. Technol. 68/69, p. 285, 1994 https://doi.org/10.1016/0257-8972(94)90175-9
  6. Mandl, S., Brutscher, J. and Gunzel, R., 'Nuclear instruments and methods in physics,' Research Section B 112, pp. 252-254, 1996
  7. Liu, A., Wang, X. and Tang, B., 'Improve retained dose and impact energy of inner surface plasma immersion ion implantation using long pulse duration with deflecting electric field, ' Surf. Coat. Technol. 149, pp. 114-118, 2002 https://doi.org/10.1016/S0257-8972(01)01494-3
  8. Conrad, J. R. and Dodd, R. A., 'Plasma source ion implantation: A new, cost-effective, non-line-of-sight technique for ion implantation of materials,' Surf. Coat. Technol., pp. 927-937, 1988
  9. Chen, A., Scheure, J. T., Ritter, C., Alexander, R. B. and Conrad, J. R., 'Comparison between conventional and plasma source ion-im planted femoral knee components,' Appl. Phys., Vol. 70, p. 5767, 1991
  10. Mitsuo, A. and Uchida, S., 'Effect of pulse bias voltage and nitrogen pressure on nitrogen distribution in steel substrate by plasma immersion ion implantation of nitrogen, ' Surf. Coat. Technol., Vol. 186, pp. 196-199, 2004 https://doi.org/10.1016/j.surfcoat.2004.04.021
  11. Wang, H. H. and Tian, M. B., 'Ions Beam Surface Strength,' pp. 131-132, 1988
  12. Gao, C. Q., 'Metal Tribology,' pp. 131-132, 1988