Journal of the Korean Ceramic Society (한국세라믹학회지)

The Korean Ceramic Society (한국세라믹학회)
권호 표지
DOI QR코드

DOI QR Code

Ceramics Body Development Using Waste Whiteware

백자 파도자기를 활용한 도자기 소지 개발

  • Lee, Jea-Il (Department of Ceramic Engineering, Myongji University) ;
  • Lee, Yong-Seok (Material Research Institute for Sustainable Development, AIST Chubu, Japan) ;
  • Lee, Byung-Ha (Department of Ceramic Engineering, Myongji University)
  • 이제일 (명지대학교 세라믹공학과) ;
  • 이용석 (일본 산업기술총합연구소 중부센터 Sustainable연구부문 세라믹응용부재 연구그룹) ;
  • 이병하 (명지대학교 세라믹공학과)
  • Published : 2006.10.31
Download PDF
⟨ Previous Next ⟩

Abstract

Ceramics manufacturers in the nation produced more than 5000 tons of ceramics wastes a year increasing industrial waste quantity: However, almost no researches were made to reduce environmental pollution and to recycle waste ware. In this study, white ware scraps that were produced at Icheon, Gyeonggi-do were recycled to make use of them as raw materials of ceramics body and to develop new ceramics body that had economic advantages and good quality. The findings showed that the addition of waste ware had limit of 20 wt% considering molding. The addition of waste ware of 20 wt% to white ware lowered baking temperature of the white ware that was added by waste ware of 20 wt% by 30$^{\circ}C$ than existing white ware, and property values were good, for instance, porosity of 3% in average and water absorptivity of 2% in average, and the bending strength recorded more than 800 kgf/$cm^2$ to be high than that of existing white ware being sold in market. The waste ware could be used to produce new ware body and to recycle resources and to solve environmental problems caused by burial and to improve property of ceramics and to save transportation costs as well as baking costs.

Keywords

References

  1. W. D. Kingery, H. K. Bowen, and D. R. Uhlmann, 'Introduction to Ceramics,' John Wiley & Sons, 1976
  2. A. J. Leonard, 'Structural Analysis of the Transition Phase in the Kaolinite-Mullite Thermal Sequence,' J. Am. Ceram. Soc., 60 [1-2] 37-43 (1977) https://doi.org/10.1111/j.1151-2916.1977.tb16081.x
  3. J. H. Lee, E. S. Na, and S. C. Choi, 'A Study on the Effect of Residual Stress between Body and Glaze of Pottery on the Mechanical Strength,' Kor. J. Mat. Res., 9 [2] 181-86 (1999)
  4. Y. G. Jung, 'Effect of Firing Temperature on Mechanical Property and Contact Damage in Pottery(in Korean),' J. Kor. Ceram, Soc., 35 [12] 1343-50 (1998)
  5. W. M. Carty and U. Senapati, 'Porcelain-Raw Materials, Processing, Phase Evolution and Mechanical Behavior,' J. Am. Ceram. Soc., 81 [1] 3-20 (1998) https://doi.org/10.1111/j.1151-2916.1998.tb02290.x
  6. F. H. Norton, 'Ceramic for the Artist Potter,' Wesley Publishing Co. Inc., 1956
  7. F. H. Norton, 'Fine Ceramics (Technology and Applications),' McGraw-Hill, 1970
  8. D. Rhodes, 'Clay and Glazes for the Potter,' Chilton Book Company, 1973
  9. R. C. Bradt, 'A High-Tech Approach to a Traditional Ceramic-The Toughness of Porcelain,' pp. 15-22 in proceeding of International Symposium on Fine Ceramics Arita 86, 1986
  10. L. Mattyasovszky-Zsolnay, 'Mechanical Strength of Porcelain,' J. Am. Ceram. Soc., 40 299-306 (1957) https://doi.org/10.1111/j.1151-2916.1957.tb12626.x
  11. N. Yamamoto, 'Mechanical Strength of Porcelain,' NGK Review, 25 17-22 (1962)
  12. S. I. Warshaw and R. Silica, 'Comparison of Strength of Triaxial Porcelains Containing Alumina and Silica,' J. Am. Ceram. Soc., 50 [7] 337-42 (1967) https://doi.org/10.1111/j.1151-2916.1967.tb15128.x
  13. A. W. Norris, D. Taylor, and I. Thorpe, 'Range Curve: An Experimental Method for the Study of Vitreous Pottery Bodies,' Trans. J. Br. Ceram. Soc., 78 102-08 (1992)
  14. Y. Kobayashi, O. Ohira, Y. Ohashi, and E. Kato, 'Effect of firing Temperature on Bending Strength of Porcelain for Tableware,' J. Am. Ceram. Soc., 75 [7] 1801-06 (1992) https://doi.org/10.1111/j.1151-2916.1992.tb07200.x
  15. H. J. Lim, S. C. Choi, E. S. Lee, and J. S. Lee, 'Effect of Processing Parameters on the Densification-Behaviors by Low Shrinkage in Clay Materials(in Korean),' J. Kor. Ceram. Soc., 33 [7] 725-34 (1996)
  16. E. S. Lee, 'Studies on the Mechanical Properties of Porcelain Bodies(in Korean),' J. Kor. Ceram. Soc., 11 [3] 69- 79 (1974)
  17. Andreola-F, Barbieri-L, Corradi-A, Lancellotti-I, and Manfredini- T, 'The Possibility to Recycle Solid Residues of the Municipal Waste Incineration into a Ceramic Tile Body,' J. Mat. Sci., 36 [20] 4869-73 (2001) https://doi.org/10.1023/A:1011823901409
  18. I. Agote, A. Odriozola, N. Gutierrez, A. Santamaria, J. Quintanilla, P. Coupelle, and J. Soares, 'Rheological Study of Waste Porcelain Feedstocks for Injection-Molding,' J. Eur. Ceram. Soc., 21 [16] 2843-53 (2001) https://doi.org/10.1016/S0955-2219(01)00210-2
  19. J. O. Hong, S. G. Kang, K. G. Lee, Y. T. Kim, Y. J. Kim, J. H. Kim, and M. S. Park, 'Characteristics of Sintered Bodies Made from the System of Paper Sludge Ash-Fly Ash- Clay(in Korean),' J. Kor. Ceram. Soc., 38 [10] 908-13 (2001)
  20. M. Pelino, C. Cantalini, F. Veglio, and P. P. Plescia, 'Crystallization of Glasses Obtained by Recycling Goethite Industrial-Wastes to Produce Glass-Ceramic Materials,' J. Mat. Sci., 29 [8] 2087-94 (1994) https://doi.org/10.1007/BF01154684
  21. S. W. Lee, H. J. Kim, and E. H. Kim, 'Control of Permanent Shrinking of Recycled Castable Refractories from Waste Refractories of $Al_2O_3-SiO$(in Korean),' J. Kor. Ceram. Soc., 29 [1] 15-22 (1992)
  22. H. Schneider, K. Okada, and J. A. Pask, 'Mullite and Mullite Ceramics,' John Wiley & Sons, 1994
  23. I. S. Kim, S. W. Kang, J. S. Park, M. W. Lee, B. H. Lee, and K. H. Lee, 'Influence of Mullite-Seed on the Mullite Synthesis from Various Compositions,' J. Kor. Ass. Crystal Growth, 10 [1] 48-54 (2000)

Cited by

  1. Development of ceramic glazes utilizing wasted porcelains vol.21, pp.2, 2011, https://doi.org/10.6111/JKCGCT.2011.21.2.087