DOI QR코드

DOI QR Code

Contact Heat Transfer Coefficient for Finite Element Analysis in Warm Forging Processes

온간단조 공정의 계면열전달계수

  • 강종훈 (발레오 전장 시스템(주)) ;
  • 고병호 (발레오 전장 시스템(주)) ;
  • 제진수 (경상대학교 수송기계공학부) ;
  • 강성수 (부산대학교 정밀기계공학과)
  • Published : 2006.04.01

Abstract

Heat transfer coefficients have great influence on finite element analysis results in elevated temperature forging processes. Experimentally calculated contact heat transfer coefficient is not suitable for one-time finite element analysis because analyzed temperature will be appeared to be too low. To get contact heat transfer coefficient for one-time finite element analysis, tool temperature in operation was measured with thermocouple and repeated finite element analysis was performed with experimentally calculated contact and cooling heat transfer coefficient. Surface temperature of active tool was obtained comparing measurement and analysis results. Contact heat transfer coefficient for one-time finite element analysis was achieved analyzing surface temperature between repeated finite element analysis and one-time finite element analysis results.

Keywords

References

  1. M. Knoerr, 1996, Fatigue failure of cold forging tooling : causes and possible solutions through fatigue analysis, JMPT. Vol. 46, pp. 57-71
  2. M. J. Liou, H. S. Hasiano, 1989, Prediction of die wear in high speed hot upset forging, ERC/NSM Report, No. 99, pp. 33-39
  3. J. H. Kang, 1999, A study on a die wear model considering thermal softening: (I) construction of the wear model, JMPT, Vol. 96, pp. 53-58 https://doi.org/10.1016/S0924-0136(99)00103-X
  4. J. H. Kang, 1999, A study on a die wear model considering thermal softening: (II) Application of the suggested wear model, JMPT, Vol. 94, pp. 183-188 https://doi.org/10.1016/S0924-0136(99)00104-1
  5. G. D. Monika, 1999, The effect of hardening layers and technological lubricants on heat exchange between workpiece and die, Comp. and. Struc., Vol.72, pp. 165-172 https://doi.org/10.1016/S0045-7949(99)00040-1
  6. D. J. Jeong, B. M, Kim, 2001, Effects of surface treatments and lubricants for warm forging die life, JMPT, Vol. 113, pp.544-550 https://doi.org/10.1016/S0924-0136(01)00693-8
  7. 권진욱, 이영선, 2005, Al6061 열간단조시 계면열전달계수에 관한 연구, 한국소성가공학회 춘계학술대회, pp. 219-222
  8. H. Grass, 2003, 3-D Simulation of hot forming and microstructure evolution, Comp. Mat. Sci., Vol. 28, pp. 469-477 https://doi.org/10.1016/j.commatsci.2003.06.003
  9. Victor Vaquez, 2000, Die design for flashless forging of complex parts, JMPT, Vol.98, pp. 81-89 https://doi.org/10.1016/S0924-0136(99)00308-8
  10. Veronique Garat, 2004, Influence of design and process parameters on service life of nut hot forging die, JMPT, Vol.147, pp. 359-369 https://doi.org/10.1016/j.jmatprotec.2003.01.002
  11. S. Sen, B. Aksakal, 2000, Transient and residual thermal stresses in quenched cylindrical bodies, Inter. J. Mech. Sci., Vol.42, pp. 2013-2029 https://doi.org/10.1016/S0020-7403(99)00063-6
  12. 진민호, 강성수, 2004, 냉간단조용 SCM420 강의 퀜칭 시 열전달 예측모델 개발, 한국소성가공학회지, Vol.13, No.5. pp. 441-448
  13. J. U. Jang, 2002, FE Program development for predicting thermal deformation in heat treatment, JMPT, Vol.130, pp. 546-550 https://doi.org/10.1016/S0924-0136(02)00802-6