Transactions of Materials Processing (소성∙가공)

The Korean Society for Technology of Plasticity and materials processing (한국소성∙가공학회)
권호 표지
DOI QR코드

DOI QR Code

Molding Stability of Hydro-Mechanical High Speed Injection Molding for Thin-Wall(0.3mm) LGP

박판(0.3mm) 도광판 성형을 위한 유압식 고속사출성형의 성형 안정성 연구

  • 황철진 (한국생산기술연구원 정밀금형팀) ;
  • 김종선 (한국생산기술연구원 정밀금형팀) ;
  • 오정길 (한국생산기술연구원 정밀금형팀) ;
  • 정철 (한국생산기술연구원 정밀금형팀) ;
  • 안희정 ((주)선우중공업 부설연구소) ;
  • 허영무 (한국생산기술연구원 정밀금형팀) ;
  • 김종덕 (한국생산기술연구원 정밀금형팀) ;
  • 윤경환 (단국대학교 기계공학과)
  • Published : 2008.12.01
Download PDF
⟨ Previous Next ⟩

Abstract

Recently, products of electronic industry and related parts are required to have the thickness thinner and thinner to reduce the part weight. To go with this trend, LGP(light guide plate) of LCD-BLU(Liquid Crystal Display-Back Light Unit: It is one of kernel parts of LCD) for cell phone has the thickness of ${\sim}0.3mm$ and the battery case of cell phone has ${\sim}0.25mm$. Accordingly, high speed injection molding is required to mold products which have thinner parts. To achieve high speed injection and proper control of hydraulic unit, various design was applied to conventional injection unit. In the present paper, we concentrated on the molding stability of hydro-mechanical high speed injection machine to make an LGP of 0.3mm thickness.

Keywords

References

  1. M. C. Song, Z. Liu, M. J. Wang, T. M Yu, D. Y. Zhao, 2007, Research on effects of injection process parameters on the molding process for ultra-thin wall plastic parts, Journal of Materials Processing Technology, Vol. 187-188, pp. 668-671 https://doi.org/10.1016/j.jmatprotec.2006.11.103
  2. S. C. Chen, W. L. Liaw P. L. Su, M. H. Chung, 2003, Investigation of Mold Plate Separation in Thin-Wall Injection Molding, Advances in Polymer Technology, Vol. 22, pp. 306-319 https://doi.org/10.1002/adv.10058
  3. Y. K. Shen, P. H. Yeh, J. S. Wu, 2001, Numerical simulation for thin wall injection molding of fiberreinforced thermoplastics, Int. Communications in Heat and Mass Transfer, Vol. 28, pp. 1035-1042 https://doi.org/10.1016/S0735-1933(01)00307-4
  4. J. H. Yun, K. Park, O. K. Kwon, 2007, Improvement of moldability for Ultra Thin-Wall Molding with Micro-Patterns, Trans. of the Korean Society of Mech. Eng. (A), Vol. 31, pp. 556-561 https://doi.org/10.3795/KSME-A.2007.31.5.556
  5. Y. S. Do, C. J. Hwang, K. H. Yoon, 2008, A Study on the Improvement of Optical Efficiency for The 2 inch LGP Considering Injection Molding Characteristics, Trans. of Materials Processing, Vol. 17, pp. 322-327 https://doi.org/10.5228/KSPP.2008.17.5.322

Cited by

  1. Measurement of Viscosity and Numerical Analysis of High Speed Injection Molding for Thin-Walled LGP vol.23, pp.1, 2014, https://doi.org/10.5228/KSTP.2014.23.1.41