International Journal of Precision Engineering and Manufacturing

  • 제9권4호
  • /
  • Pages.22-25
  • /
  • 2008
  • /
  • 2234-7593(pISSN)
  • /
  • 2005-4602(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

Dynamic Response Measurement of the Head Arm Assembly of a Hard Disk Drive by Numerical Analysis and Experiments

  • Parlapalli, Madhusudhana R (School of Mechanical and Aerospace Engineering, Nanyang Technological University) ;
  • Bin, Gu (School of Mechanical and Aerospace Engineering, Nanyang Technological University) ;
  • Dongwei, Shu (School of Mechanical and Aerospace Engineering, Nanyang Technological University) ;
  • Fujii, Yusaku (Department of Electronic Engineering, Gunma University)
  • 발행 : 2008.10.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The dynamic response of the head arm assembly (HAA) of a hard disk drive to an impact load was obtained from a 3D non-linear finite element model using ANSYS/LS-DYNA and from experiments using a modified levitation mass method (LMM). In the finite element model, the impact load was created by modeling the mass as a rigid body and making it collide with the HAA. The velocity, displacement, acceleration, and inertial force of the mass were then obtained from the time history data of the finite element analysis. In the LMM, a mass that was levitated with an aerostatic linear bearing, and hence encountered negligible friction, was made to collide with the actuator arm, resulting in a dynamic bending test for the arm. During the collision, the Doppler frequency shift of the laser beam reflected from the mass was accurately measured with an optical interferometer. The velocity, displacement, acceleration, and inertial force of the mass were accurately calculated from the measured time-varying Doppler frequency shift. A good correlation between the experimental data and FEA results was observed. The FEA was also used to investigate the dynamic response of the HAA to impact by different masses.

키워드

참고문헌

  1. Ganapathi, S. K., Donovan, M. and Hsia, Y. T., 'Contact force measurement at the head/disk interface for contact recording heads in magnetic recording,' Proceeding of SPIE, The International Society for Optical Engineering, Vol. 2604, pp. 236-243, 1995
  2. Matsumoto, M., Iida, A. and Hamaguchi, T., 'Measurement of slider/disk collision forces using acoustic emission source wave analysis,' STLE Tribology Transactions, Vol. 36, No. 4, pp. 736- 740, 1993 https://doi.org/10.1080/10402009308983219
  3. Burger, G. J., 'A slider motion monitoring system: measuring contact and friction forces in rigid disk storage devices,' Thesis, Dept. of Applied Physics, Univ. of Twente, pp. 41-82, 1995
  4. Fujii, Y., 'Optical method for accurate force measurement: dynamic response evaluation of an impact hammer,' Optical Engineering, Vol. 45, No. 2, pp. 023002-1-7, 2006 https://doi.org/10.1117/1.2170713
  5. Fujii, Y. and Valera, J., 'Impact force measurement using an inertial mass and a digitizer,' Measurement Science Technology, Vol. 17, No. 4, pp. 863-868, 2006 https://doi.org/10.1088/0957-0233/17/4/035
  6. Fujii, Y., 'Frictional characteristics of an aerostatic linear bearing,' Tribology International, Vol. 39, No. 9, pp. 888-896, 2006 https://doi.org/10.1016/j.triboint.2005.07.040
  7. Fujii, Y., 'Impact response measurement of an accelerometer,' Mechanical Systems and Signal Processing, Vol. 21, No. 5, pp. 2072-2079, 2007 https://doi.org/10.1016/j.ymssp.2006.08.014
  8. Han, M. S. and Cho, J. U., 'Dynamic analysis of 3 ponit bend specimens under high loading rates,' International Journal of Precision Engineering and Manufacturing, Vol. 1, No. 2, pp. 84-93, 2000
  9. Lee, Y. S., Yoon, Y. K and Yoon, H. S., 'Dynamic fracture toughness of Chevron-notch ceramic specimens measured in Split Hopkinson Pressure Bar,' International Journal of Precision Engineering and Manufacturing, Vol. 3, No. 3, pp. 69-75, 2002
  10. Dokko, W. and Kim, M. S., 'Analysis of elasto-plastic dynamic behavior of plates subjected to low velocity impact,' International Journal of Precision Engineering and Manufacturing, Vol. 6, No. 1, pp. 36-41, 2005
  11. Shu, D. W., Shi, B. J., Meng, H., Yap, F. F., Jiang, D. Z., Ng, Q. Y., Zambri, R. and Lau., J. H. T., 'The pulse width effect of single half-sine accelration pulse on the peak response of an actuator arm of hard disk drive,' Materials Science and Engineering A, Vol. 423, No.1/2, pp. 199-203, 2006 https://doi.org/10.1016/j.msea.2005.09.128
  12. Shu, D. W., Shi, B. J., Meng, H., Yap, F. F., Jiang, D. Z., Ng, Q. Y., Zambri, R. and Lau, J. H. T., 'Shock analysis of a head actuator assembly subjected to half-sine acceleration pulses,' International Journal of Impact Engineering, Vol. 34, No. 2, pp. 253-263, 2007 https://doi.org/10.1016/j.ijimpeng.2005.07.009
  13. Shi, B. J., Shu, D. W., Wang, Sh., Luo J., Meng, H., Ng, Q. Y., Lau, J. H. T. and Zambri, R., 'Drop test simulation and power spectrum analysis of a head actuator assembly in a hard disk drive,' International Journal of Impact Engineering, Vol. 34, No. 1, pp. 120-133, 2007 https://doi.org/10.1016/j.ijimpeng.2006.06.008
  14. Aristegui, J. L. and Geers, T. L., 'Shock analysis of a disk-drive assembly,' Journal of Information Storage and Processing Systems, Vol. 2, pp. 25-31, 2000
  15. Edwards, J. R., 'Finite element analysis of the shock response and head slap behavior of a hard disk drive,' IEEE Transactions on Magnetics, Vol. 35, pp. 863-867, 1999 https://doi.org/10.1109/20.753799