한국생산제조학회지 (Journal of the Korean Society of Manufacturing Technology Engineers)

  • 제19권6호
  • /
  • Pages.760-767
  • /
  • 2010
  • /
  • 2508-5093(pISSN)
  • /
  • 2508-5107(eISSN)
한국생산제조학회 (The Korean Society of Manufacturing Technology Engineers)
권호 표지

신경망을 이용한 유연디스크 가공 종단부 품질예측에 관한 연구

A study on the exit stage quality prediction of flexible disk process using neural network

  • 유송민 (경희대학교 공과대학 기계공학과)
  • 투고 : 2010.10.25
  • 심사 : 2010.11.01
  • 발행 : 2010.12.15
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Even though a flexible disk grinding process was often applied to enhance the product quality, it produced non-flat zone in the beginning and the exit (end) area. Since latter area is susceptible to poor product quality with burn mark, careful analysis is required to cope with such degradation. The flexible disk grinding exit stage was analyzed for workpiece length, wheel speed, depth of cut and feed. The exit stage qualities defined as exit stage ratio and exit stage angle or slope was characterized. A neural network application results reveled that exit stage characteristics was predicted more accurately without workpiece dimension with minimum error of 1.3%.

키워드

참고문헌

  1. Lee, J. I., Kim, T. W., Park, Y. W., and Kwak J. S., 2008, "A Study on Deburring Process for Thin Magnesium Plate", Proc. of KSMTE Fall Conf., pp. 302-306.
  2. Shin, T. H., Baek, S. Y., and Lee, E. S., 2009, "The Evaluation of Electrochemical Deburring on Cellular Phone External Frame", Proc. of KSMTE Spring Conf., pp. 135-140.
  3. Park, D. S., Choi, Y. H., and Kang, D. K., 2003, "The Deburring of the Actuator Arm of HDD for PC", Proc. of KSMTE Spring Conf., pp. 155-160.
  4. Song, M. K., Baek, J. Y., Shin, K. S., and Yoo, S. M., 2001, "Quality Measurement of Deburring Product using Image Processing", Proc. of KSMTE Spring Conf., pp. 119-124.
  5. Kurfess, T. R., 1988, "Verification of Dynamic Grinding Model", Trans. ASME, J. of Dynmic Sys and Control, Vol. 110, No. 4, pp. 403-409. https://doi.org/10.1115/1.3152703
  6. Yoo, S. M., Choi, M. J., and Kim Y. J., 2000, "Model Development of Flexible Disk Grinding Process", KSME international J., Vol. 14, No. 10, pp. 1114-1121. https://doi.org/10.1007/BF03185065
  7. Yoo, S. M., 1996, "A Study on the Flat Surface Generation Using Flexible Disk Grinding", J. of the KSPE, Vol. 13, No. 7, pp158-166.
  8. Yoo, S. M., 2007, "A Study on the Flat Surface Zone of the Flexible Disk Grinding System", Transaction of KSMTE, Vol. 16, No. 6, pp. 125-132.
  9. Kim, H. G. and Sim, J. H., 2007, "Performance Evaluation of Chip Breaker Utilizing Neural Network", Transaction of KSMTE, Vol. 16, No. 3, pp. 54-74.
  10. Prasopchaichana, K. and Kwon, O. Y., 2008, "Sensor Fusion and Neural Network analysis for Drill-Wear Monitoring", Transaction of KSMTE, Vol. 17, No.1, pp. 77-85.
  11. Yoo, S. M., 2008, "A Study on the Flexible Disk Grinding Process Parameter Prediction Using Neural Network", Transaction of KSMTE, Vol. 17, No. 5, pp. 123-130.
  12. Yoo, S. M., 2009, "A Study on the Flexible Disk Deburring Process Arc Zone Parameter Prediction Using Neural Network", Transaction of KSMTE, Vol. 18, No. 6, pp. 681-689.