Estimation of Cooling Rate in Bulk Amorphous Alloys by Separate Cooling Process

  • Kang, Bok-Hyun (Department of Materials Engineering, Korea University of Technology and Education) ;
  • Choi, Seong-Pil (Department of Materials Engineering, Korea University of Technology and Education) ;
  • Kim, Ki-Young (Department of Materials Engineering, Korea University of Technology and Education)
  • Received : 2010.09.07
  • Accepted : 2010.09.24
  • Published : 2010.10.31

Abstract

벌크 비정질 합금의 특성상 점도가 높고, 냉각속도가 빨라 냉각되는 합금의 온도를 직접 측정하는 것은 곤란하므로, 측정에 의하여 냉각속도를 구하는 것은 매우 어렵다. 본 연구에서는 합금의 온도를 직접 측정하는 대신 금형의 온도를 측정하고, 측정된 금형의 온도를 상용 열해석 프로그램을 이용한3차원 계산 결과와 비교, 보정하는 역문제 기법을 사용하여 Cu계와 Zr계 벌크 비정질합금의 냉각속도를 예측하였다. 예측된 냉각속도는 금형온도와 시편의 두께에 따라Cu계의 경우는 284~300 K/s, Zr계는 279~289 K/s로, 초기 금형온도의 영향은 크지 않은 것으로 나타났다. 전산모사 결과와 달리 금형을 수냉한 쪽보다 가열한 쪽의 응고중 냉각속도가 빨라 조직이 더 미세한 것으로 나타났는데, 이는 응고중 금형과 주물간에 에어갭의 형성으로 열전달을 방해 받은 영향으로 사료된다.

Keywords

References

  1. H. S. Chen, Rep. Prog. Phys., 43(1980) 353 https://doi.org/10.1088/0034-4885/43/4/001
  2. Y. H. Kim, A. Inoue, T. Masumoto, "Ultrahigh tensile strengths of Al88Y2Ni9M1 (M = Mn or Fe) amorphous alloys containing finely dispersed fcc-A1 particles", Mater. Trans. JIM, 31 (1990) 747 https://doi.org/10.2320/matertrans1989.31.747
  3. T. Masumoto, "Materials science of amorphous materials", Ohmu, Tokoyo, 1982
  4. L. E. Luborsky, "Amorphous metallic alloys", Butterworths, London, 1983
  5. N. Matsumoto, R. Matsumoto, N. Miyazaki, "Estimation of Shear-banding resistance in metallic glass containing nanocrystalline particles", J. of non-crystalline solids, Volume 355 Page: 29
  6. Seong-Pil Choi, Bok-Hyun Kang, Ki-Young Kim, "Microstructural change of bulk amorphous alloys by separate cooling", Proc. 2nd Int. Conf. on Japan-Korea workshop for young foundry engineers, Jeju island, KOREA, July (2005) JFES and KFS, Page(s): 225-226
  7. Seong-Pil Choi, "Microstructural change of bulk amorphous alloys by separate cooling", master thesis, Korea University of Technology and Education, KOREA, 2007
  8. W. L. Johnson, "Bulk glass-forming metallic alloys", MRS Bulletin, 10 (1999) 47
  9. S. Y. Shin, J. H. Kim, D. M. Lee, J. K. Lee, H. J. Kim, H. G. Jeong, J. C. Bae, "New Cu-based bulk metallic glasses with high strength of 2000 MPa", Mat. Sci. For, 945 (2004) 449-452
  10. Hye-Sook Joo, "Evaluation on liquid formability of bulk amorphous ally", master thesis, Korea University of Technology and Education, KOREA, 2005
  11. C. Way, P. Wadhwa, R. Busch, "The influence of shear rate and temperature on the viscosity and fragility of the $Zr_{41.2}Ti_{13.8}Cu_{12.5}Ni_{10.0}Be_{22.5}$ metallic-glass-forming liquid", Acta Mater, 2977 (2007) 55
  12. Ki-Young Kim, "Analysis of gap formation at mold-shell interface during solidification of aluminium alloy plate", ISIJ International, 5 (2003) 647-65