DOI QR코드

DOI QR Code

Design and Manufacture of Ultrasonic Vibration Drawing Tool

유한요소해석을 이용한 초음파 진동 인발기 설계 및 제작

  • 이경훈 (부산대학교 대학원 정밀가공시스템) ;
  • 김병민 (부산대학교 기계공학부)
  • Received : 2010.08.16
  • Accepted : 2010.09.29
  • Published : 2010.10.01

Abstract

In ultrasonic vibration drawing, the drawing forces can be reduced by applying ultrasonically oscillating dies. Ultrasonic vibration drawing has been considered as a means of accommodating high-level drawing processes such as shaped wire, ultrafine wire, and the wire drawing operation in semidry or dry condition. Prior studies were attempted to analyze the mechanism of improved drawing performances, such as reduced drawing force and improved lubrication characteristic. However, researches on design rule for ultrasonic vibration drawing system are not yet carried out. The principal objectives of this work are to design a set of tooling capable to superimpose the oscillations and to observe by experiments the influence of the ultrasonic oscillations on the wire drawing.

Keywords

References

  1. M. Kobayashi, 1998, The present situation of cold drawn special section, J. JSTP, Vol. 39, No. 447, pp. 335-337.
  2. Failure analysis and prevention, Metal Handbook, 8th ed., Vol. 10, ASM Handbook.
  3. C. E. Winsper, G. R. Dawson, D. H. Sansome, 1970, An introduction to the mechanics of oscillatory metalworking, Met. Mater., pp. 158-162.
  4. F. Blaha, B. Langeneker, 1959, Plastizitatsuntersuch ungen von metallkristallen in ultraschallfeld, Acta Metallurgica, Vol. 7, Issue 2, pp. 93-100. https://doi.org/10.1016/0001-6160(59)90114-2
  5. R. Pohlman, E. Lehfeldt, 1966, Influence of ultrasonic vibration on metallic friction, Ultrasonics, Vol. 4, pp. 178-185. https://doi.org/10.1016/0041-624X(66)90244-7
  6. M. Murakawa, M. Jin, 2001, The utility of radially and ultrasonically vibrated dies in the wire drawing process, J. Mater. Process. Technol., Vol. 113, pp. 81-86. https://doi.org/10.1016/S0924-0136(01)00635-5
  7. M. Hayashi, M. Jin, S. Thipprakmas, M. Murakawa, J. C. Hung, Y. C. Tsai, C. H. Hung, 2003, Simulation of ultrasonic-vibration drawing using the finite element method(FEM), J. Mater. Process. Technol., Vol. 140, pp. 30-35. https://doi.org/10.1016/S0924-0136(03)00699-X
  8. K. Siegert, A. Mock, 1996, Wire drawing with ultrasonically oscillating dies. J. Mater. Process. Technol., Vol. 60, pp. 657-660. https://doi.org/10.1016/0924-0136(96)02401-6
  9. J. C. Hung, C. Hung, 2005, The influence of ultrasonic-vibration on hot upsetting of aluminum alloy, Ultrasonics, Vol. 43, pp. 692-698. https://doi.org/10.1016/j.ultras.2005.03.001
  10. B. G. Lee, K. L. Kim, K. E. Kim, 2008, Design of Ultrasonic Vibration Tool Horn for Micromachining Using FEM, Trans. Kor. Soc. Machine Tool Eng.,
  11. K. J. Kang, Y. R. Roh, 2001, Design and construction of the acoustic horn for magnetostrictive ultrasonic transducer, J. Acoust. Soc. Kor., Vol. 20, pp. 57-65.
  12. E. Eisner, 1961, Complete solutions of the Webster horn equation, J. Acoust. Soc. Am., Vol. 41, pp. 1126-1146. https://doi.org/10.1121/1.1910444
  13. S. Lin, 1996, Study on the longitudinal-torsional composite mode exponential ultrasonic horns, Ultrasonics, Vol. 34, pp. 757-762. https://doi.org/10.1016/0041-624X(96)00062-5
  14. C. H. Kim, 2007, A study on the motion of the levitated object in ultrasonic near-field acoustic levitation, PhD thesis, KAIST.

Cited by

  1. FEA and Experiment Investigation on the Friction Reduction for Ultrasonic Vibration Assisted Deep Drawing vol.23, pp.7, 2014, https://doi.org/10.5228/KSTP.2014.23.7.413