Journal of the Korea Concrete Institute (콘크리트학회논문집)

Korea Concrete Institute (한국콘크리트학회)
권호 표지
DOI QR코드

DOI QR Code

Compressive Stress Distribution of Concrete for Performance-Based Design Code

성능 중심 설계기준을 위한 콘크리트 압축응력 분포

  • 이재훈 (영남대학교 건설시스템공학과) ;
  • 임강섭 ((주)서영엔지니어링) ;
  • 황도규 (영남대학교 건설시스템공학과)
  • Received : 2011.02.14
  • Accepted : 2011.04.28
  • Published : 2011.06.30
Download PDF
⟨ Previous Next ⟩

Abstract

The current Concrete Structural Design Code (2007) prescribe the equivalent rectangular stress block of the ACI 318 Building Code as concrete compressive stress distribution for design of concrete structures. The rectangular stress block may be enough for flexural strength calculation, but realistic stress-strain relationship is required for performance verification at selected limit state in performance-based design. Moreover, the ACI rectangular stress block provides non-conservative flexural strength for high strength concrete columns. Therefore a new stress distribution model is required for development of performance-based design code. This paper proposes a concrete compressive stress-strain distribution model for design and performance verification. The proposed model has a parabolic-rectangular shape, which is adopted by Eurocode 2 and Japanese Code (JSCE). It was developed by investigation of experimental test results conducted by the authors and other researchers. The test results cover high strength concrete as well as normal strength concrete. The stress distribution parameters of the proposed models are compared to those of the ACI 318 Building Code, Eurocode 2, Japanese Code (JSCE) and Canadian Code (CSA) as well as the test results.

현행 콘크리트구조설계기준(2007)은 콘크리트 구조물의 설계에 적용하는 콘크리트의 압축응력 분포로 ACI 318의 등가 직사각형 응력 분포를 규정하고 있다. 단면의 휨강도 해석에는 등가 직사각형 응력 분포가 충분하겠지만, 성능 중심 설계의 한계 상태 검증에는 실제와 가까운 압축응력-변형률 관계가 필요하다. 또 등가 직사각형 응력 분포는 고강도 콘크리트 기둥의 휨강도 해석에 비안전측의 결과를 준다는 것이 알려져 있으므로, 이를 대신하는 새로운 응력 분포 모델이 필요하다. 이 연구에서는 Eurocode와 일본 토목학회의 설계기준에서 채택하고 있는 포물선-직선 형상의 새로운 모델을 제안하였다. 이 응력 분포 모델은 이 연구에서 수행된 압축응력 분포 실험과 타 연구자들의 실험 결과를 분석하여 도출된 것으로서, 보통 강도뿐만 아니라 고강도 콘크리트를 포함한 것이다. 제안 모델의 특성은 미국 ACI 318, 캐나다 CSA, 유럽의 Eurocode, 일본 토목학회 설계기준의 응력 분포 모델과 함께 실험 결과와 비교하여 정리하였다.

Keywords

References

  1. 국토해양부, 콘크리트구조설계기준, 한국콘크리트학회, 2007, 327 pp.
  2. ACI 318-08, Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute, Farmington Hills, USA, 2002, 473 pp.
  3. Hognestad, E., Hanson, N. W., and McHenry, D., "Concrete Stress Distribution in Ultimate Strength Design," ACI Journal, Proceeding, Vol. 27, No. 3, 1955, pp. 455-479.
  4. Nedderman, H., "Flexural Stress Distribution in very High Strength Concrete," Masters Degree Thesis, Department of Civil Engineering, University of Texas at Arlington, 1973, 182 pp.
  5. Kaar, P. H., Hanson, N. W., and Capell, H. T., "Stress-Strain Characteristics of High Strength Concrete," PCA Research and Development Bulletin, RD051.01D, 1977, pp. 1-10.
  6. Ibrahim, H. H. and MacGregor, J. G., "Modification of the ACI Rectangular Stress Block for High-Strength Concrete," ACI Structural Journal, Vol. 94, No. 1, 1997, pp. 40-48.
  7. 이재훈, 손혁수, 김준범, "고강도 철근콘크리트 기둥의 실험 및 강도해석," 콘크리트학회 논문집, 11권, 1호, 1999, pp. 149-160.
  8. Lee, J. H. and Son, H. S., "Failure and Strength of High- Strength Concrete Columns Subjected to Eccentric Loads," ACI Structural Journal, Vol. 97, No. 1, 2000, pp. 75-85.
  9. Rizkalla, S., Mirmiran, A., Zia, P., Russell, H., and Mast, R., "Application of the LRFD Bridge Design Specifications to High-Strength Structural Concrete: Flexure and Compression Provisions," Report: National Cooperative Highway Research Program, Vol. 595, 2007, 28 pp.
  10. CSA, "Design of Concrete Structures (CSA Standard A23.3- 04)," Canadian Standard Association, Rexdale, Ontario, Canada, 2004, 24 pp.
  11. CEN, EN 1992, "Eurocode 2 : Design of Concrete Structures," European Committee for Standardization, 1992.
  12. JSCE, "Standard Specifications for Concrete Structures- 2002, Structural Performance Verification," JSCE Guidelines for Concrete No. 3, Japan Society of Civil Engineers, Japan, 2005, 274 pp.
  13. 김진근, 이성태, 양은익, "콘크리트의 휨 압축강도의 크기 효과," 콘크리트학회 논문집, 11권, 2호, 1999, pp. 157-165.
  14. Swartz, S. E., Nikaeen, A., Narayan Babu, H. D., Periyakaruppan, N., and Refai, T. M. E., "Structural Bending Properties of Higher Strength Concrete," High-Strength Concrete, SP-87, H. G. Russell, ed., American Concrete Institute, Farmington Hills, Mich., 1985, pp. 147-178.
  15. Rusch, H., "Tests on the Strength fo the Flexural Compression Zone," Bulletin N9. 120, Deutscher Ausschuss Fur Stahlbeton, Berlin, 1955, 94 pp.
  16. Schade, J. E., "Flexural Concrete Stress in High Strength Concrete Columns," M.A.Sc Thesis, Department of Civil Engineering, University of Calgary, Alberta, 1992, 156 pp.
  17. 국토해양부, 콘크리트표준시방서, 한국콘크리트학회, 2009, 762 pp.