DOI QR코드

DOI QR Code

Buckling behavior of strengthened perforated plates under shear loading

  • Cheng, Bin (Department of Civil Engineering, Shanghai Jiao Tong University) ;
  • Li, Chun (Department of Civil Engineering, Shanghai Jiao Tong University)
  • 투고 : 2012.02.03
  • 심사 : 2012.07.24
  • 발행 : 2012.10.25

초록

This paper is dedicated to the buckling behaviors of strengthened perforated plates under edge shear loading, which is a typical load pattern of steel plates in civil engineering, especially in plate and box girders. The square plates considered each has a centric circular hole and is simply supported on four edges in the out-of-plane direction. Three types of strengthening stiffeners named ringed stiffener (RS), flat stiffener (FSA and FSB) and strip stiffener (SSA, SSB and SSC) are mainly discussed. The finite element method (FEM) has been employed to analyse the elastic and elasto-plastic buckling behavior of unstrengthened and strengthened perforated plates. Results show that most of the strengthened perforated plates behave higher buckling strengths than the unstrengthened ones, while the enhancements in elastic buckling stress and elasto-plastic ultimate strength are closely related to stiffener types as well as plate geometric parameters including plate slenderness ratio and hole diameter to plate width ratio. The critical slenderness ratios of shear loaded strengthened perforated plates, which determine the practical buckling pattern (i.e., elastic or elasto-plastic buckling) of the plates, are also studied. Based on the contrastive analyses of strengthening efficiency considering the influence of stiffener consumption, the most efficient cutout-strengthening methods for shear loaded perforated square plates with different slenderness ratios and circular hole diameter to plate width ratios are preliminarily identified.

키워드

참고문헌

  1. ANSYS. (2009), Software package, Version 12.0.1.
  2. Azizian, Z.G. and Roberts, T.M. (1983), "Buckling and elasto-plastic collapse of perforated plates", Proceedings of the International Conference on Instability and Plastic Collapse of Steel Structures, London, August.
  3. Brown, C.J. (1990), "Elastic buckling of perforated plates subjected to concentrated loads", Comp. and Struct., 36(6), 1103-1109. https://doi.org/10.1016/0045-7949(90)90218-Q
  4. Brown, C.J. and Yettram, A.L. (1986), "The elastic stability of square perforated plates under combination of bending, shear and direct load", Thin-Walled Struct., 4(3), 239-246. https://doi.org/10.1016/0263-8231(86)90005-4
  5. Brown, C.J., Yettram, A.L. and Burnett, M. (1987), "Stability of plates with rectangular holes", J. of Struct. Eng., 113(5), 1111-1116. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:5(1111)
  6. Cheng, B. and Zhao, J. (2010), "Strengthening of perforated plates under uniaxial compression: Buckling analysis", Thin-Walled Struct., 48(12), 905-914. https://doi.org/10.1016/j.tws.2010.06.001
  7. El-Sawy, K.M. and Nazmy, A.S. (2001), "Effect of aspect ratio on the elastic buckling of uniaxially loaded plates with eccentric holes", Thin-Walled Struct., 39(12), 983-998. https://doi.org/10.1016/S0263-8231(01)00040-4
  8. El-Sawy, K.M., Nazmy, A.S. and Martini, M.I. (2004), "Elasto-plastic buckling of perforated plates under uniaxial compression", Thin-Walled Struct., 42(8), 1083-1101. https://doi.org/10.1016/j.tws.2004.03.002
  9. El-Sawy, K.M. and Martini, M.I. (2007), "Elastic stability of bi-axially loaded rectangular plates with a single circular hole", Thin-Walled Struct., 45(1), 122-133. https://doi.org/10.1016/j.tws.2006.11.002
  10. El-Sawy, K.M. and Martini, M.I. (2010), "Stability of biaxially loaded square plates with single central holes", Ships and Offshore Structures, 5(4), 283-293. https://doi.org/10.1080/17445300903566181
  11. Komur, M.A. (2011), "Elasto-plastic buckling analysis for perforated steel plates subject to uniform compression", Mech. Res. Comm., 38(2), 117-122. https://doi.org/10.1016/j.mechrescom.2011.01.001
  12. Maiorana, E., Pellegrino, C. and Modena, C. (2011), "Elasto-plastic behaviour of perforated steel plates subjected to compression and bending", Steel and Comp. Struct., 11(2), 131-147. https://doi.org/10.12989/scs.2011.11.2.131
  13. Moen, C.D. and Schafer, B.W. (2009), "Elastic buckling of thin plates with holes in compression or bending", Thin-Walled Struct., 47(12), 1597-1607. https://doi.org/10.1016/j.tws.2009.05.001
  14. Narayanan, R. and Chow, F.Y. (1984), "Ultimate capacity of uniaxially compressed perforated plates", Thin-Walled Struct., 2(3), 241-264. https://doi.org/10.1016/0263-8231(84)90021-1
  15. Narayanan, R. and Rockey, K.C. (1981), "Ultimate load capacity of plate girders with webs containing circular cut-outs", Proceedings of the Institution of Civil Engineers, London, March.
  16. Paik, J.K. (2007), "Ultimate strength of perforated steel plates with a single circular hole under axial compressive loading along short edges", Ships and Offshore Struct., 2(4), 355-360. https://doi.org/10.1080/17445300701623531
  17. Paik, J.K. (2007), "Ultimate strength of perforated steel plates under edge shear loading", Thin-Walled Struct., 45(3), 301-306. https://doi.org/10.1016/j.tws.2007.02.013
  18. Paik, J.K. (2008), "Ultimate strength of perforated steel plates under combined biaxial compression and edge shear loads", Thin-Walled Struct., 46(2), 207-213. https://doi.org/10.1016/j.tws.2007.07.010
  19. Pellegrino, C., Maiorana, E. and Modena, C. (2009), "Linear and non-linear behaviour of steel plates with circular and rectangular holes under shear loading", Thin-Walled Struct., 47(6-7), 607-616. https://doi.org/10.1016/j.tws.2008.11.001
  20. Sabir, A.B. and Chow, F.Y. (1983), "Elastic buckling of flat panels containing circular and square holes", Proceedings of the international conference on instability and plastic collapse of steel structures, London, August.
  21. Shanmugam, N.E. and Narayanan, R. (1982), "Elastic buckling of perforated square plates for various loading and edge conditions", Proceedings of the international conference on finite element methods, Shanghai, August.
  22. Shanmugam, N.E., Thevendran, V. and Tan, Y.H. (1999), "Design formula for axially compressed perforated plates", Thin-Walled Struct., 34(1), 1-20. https://doi.org/10.1016/S0263-8231(98)00052-4
  23. Wang, G., Sun, H., Peng, H. and Uemori, R. (2009), "Buckling and ultimate strength of plates with openings", Ships and Offshore Structures, 4(1), 45-53.

피인용 문헌

  1. Compression tests of cold-formed channel sections with perforations in the web vol.16, pp.6, 2014, https://doi.org/10.12989/scs.2014.16.6.657
  2. Opening reinforcement for box-section walls containing continuous elliptical holes in steel pylons vol.103, 2014, https://doi.org/10.1016/j.jcsr.2014.08.002
  3. Strengthening of perforated walls in cable-stayed bridge pylons with double cable planes vol.18, pp.4, 2015, https://doi.org/10.12989/scs.2015.18.4.811
  4. Axial buckling of perforated plates reinforced with strips and middle tubes vol.85, 2017, https://doi.org/10.1016/j.mechrescom.2017.07.015
  5. Nonlinear and post-buckling responses of FGM plates with oblique elliptical cutouts using plate assembly technique vol.34, pp.2, 2020, https://doi.org/10.12989/scs.2020.34.2.227
  6. Effect of crack location on buckling analysis and SIF of cracked plates under tension vol.35, pp.2, 2012, https://doi.org/10.12989/scs.2020.35.2.215
  7. Shear behavior of stiffened single perforated lean duplex stainless steel (LDSS) rectangular hollow beams vol.176, pp.None, 2021, https://doi.org/10.1016/j.jcsr.2020.106377