DOI QR코드

DOI QR Code

Detection of Delamination Crack for Polymer Matrix Composites with Carbon Fiber by Electric Potential Method

  • Shin, Soon-Gi (Department of Advanced Materials Engineering, College of Samcheok, Kangwon National University)
  • Received : 2012.12.21
  • Accepted : 2013.02.14
  • Published : 2013.02.27

Abstract

Delamination crack detection is very important for improving the structural reliability of laminated composite structures. This requires real-time delamination detection technologies. For composite laminates that are reinforced with carbon fiber, an electrical potential method uses carbon fiber for reinforcements and sensors at the same time. The use of carbon fiber for sensors does not need to consider the strength reduction of smart structures induced by imbedding sensors into the structures. With carbon fiber reinforced (CF/) epoxy matrix composites, it had been proved that the delamination crack was detected experimentally. In the present study, therefore, similar experiments were conducted to prove the applicability of the method for delamination crack detection of CF/polyetherethereketone matrix composite laminates. Mode I and mode II delamination tests with artificial cracks were conducted, and three point bending tests without artificial cracks were conducted. This study experimentally proves the applicability of the method for detection of delamination cracks. CF/polyetherethereketone material has strong electric resistance anisotropy. For CF/polyetherethereketone matrix composites, a carbon fiber network is constructed, and the network is broken by propagation of delamination cracks. This causes a change in the electric resistance of CF/polyetherethereketone matrix composites. Using three point bending specimens, delamination cracks generated without artificial initial cracks is proved to be detectable using the electric potential method: This method successfully detected delamination cracks.

Keywords

References

  1. N. Shinya, Frontier of Next-Generation Structural Materials- Impact on Society and Industry, p.97, cmcbooks Co., Tokyo, Japan (2008).
  2. A. D. Kersey, in Proceedings of the First World Conference on Structural Control(Los Angeles, CA, August 1994), Plenary 3.
  3. S. F. Masri, M. S. Agbabian, A. M. Abdel-Ghaffar, M. Higazy, R. O. Claus and M. J. de Vries, J. Eng. Mech., 120, 1696 (1994). https://doi.org/10.1061/(ASCE)0733-9399(1994)120:8(1696)
  4. C. I. Merzbacher, A. D. Kersey and E. J. Friebele, Smart Mater. Struct., 5, 196 (1996). https://doi.org/10.1088/0964-1726/5/2/008
  5. C. Ishida, Handbook of Electronic Materials, p. 769, ed. K. Z. Asakura, Asakura Shoden, Tokyo, Japan (2006).
  6. S. G. Shin, Kor. J. Mater. Res., 20, 271(2010) (in Korean). https://doi.org/10.3740/MRSK.2010.20.5.271
  7. Y. Okuhara, S. G. Shin, H. Matsubara, H. Yanagida and N. Takeda, Proc. SPIE, 4328, 314 (2001). doi:10.1117/12.435534.
  8. A. Todoroki, H. Kobayashi and K. Matsuura, J. Jpn. Soc. Compos. Mater., 21, 89 (1995) (in Japanese). https://doi.org/10.6089/jscm.21.89
  9. S. G. Shin, Electron. Mater. Lett., 6, 65 (2010).
  10. S. G. Shin, Kor. J. Met. Mater., 48, 867 (2010).
  11. S. G. Shin and I. K. Kwon, Electron. Mater. Lett., 7, 249 (2011). https://doi.org/10.1007/s13391-011-0913-1
  12. S. G. Shin, Kor. J. Mater. Res., 21(4), 196 (2011) (in Korean). https://doi.org/10.3740/MRSK.2011.21.4.196
  13. S. G. Shin, Kor. J. Mater. Res., 21(9), 477 (2011) (in Korean). https://doi.org/10.3740/MRSK.2011.21.9.477